Wireless connection of office equipment significantly simplifies work, eliminating unnecessary wires and allowing you to print from any device in the house. Model HP Deskjet Ink Advantage 3525 is a popular budget solution that supports local area network operation. However, initial setup Wi-Fi connections often raises questions among users who are encountering device drivers and menus for the first time.
Integrating a printer into your home network requires a sequential process. You need to ensure that your router is working properly and that the printer is within a strong signal range. Incorrectly following the steps or entering the wrong password can result in connection indicator The light will blink, but printing won't start. In this guide, we'll cover all the current methods for activating wireless mode.
There are several connection methods: via a computer with installed software, using technology WPS or using mobile devices. The choice of a specific method depends on your preferences and available equipment. The main thing is to strictly follow the algorithm to avoid configuration errors and ensure stable operation. printing device in the future.
Equipment preparation and compatibility testing
Before you begin setup, you need to inspect your equipment. Make sure your router supports the standards. 802.11 b/g/n, since older printer models may not see new generation networks Wi-Fi 6 or they may become unstable. It's also critical that the computer or smartphone you plan to use for control is on the same network as the one you plan to connect the MFP to.
Turn on the printer and wait for the self-test cycle to complete. The power light on the control panel will illuminate. If the device was previously used on a different network, it's recommended to reset the network settings to factory defaults to avoid IP address conflicts. To do this, press and hold the wireless button and the cancel button simultaneously for a few seconds.
⚠️ Important: Make sure the printer has cartridges installed. Some models HP Deskjet Block network setup functions if there are no ink tanks or if the ink tank access door is open.
Check your network type. If your router broadcasts signals on both 2.4 GHz and 5 GHz frequencies under the same name, the printer may attempt to connect to the 5 GHz band, which it doesn't support. In this case, it's best to separate the networks in your router or temporarily disable the high-frequency band during setup.
Using WPS technology for fast synchronization
The easiest way that does not require entering a password is to use technology WPS (Wi-Fi Protected Setup). This method is ideal if you don't want to search for drivers or manually enter a complex security key. Your router must also support this feature, which is true for most modern models.
Click the button Wireless on the printer's control panel. The indicator light will begin flashing, indicating that pairing is ready. Within two minutes, press the WPS button on your router. This is usually indicated by a corresponding icon or two arrows forming a circle.
- 📶 Wait until the wireless indicator on the printer stops flashing and turns solid blue - this indicates a successful connection.
- 🖨️ Print a network configuration report by pressing the wireless button and the information button at the same time to check the IP address.
- 🔒 If the indicator flashes blue and white alternately, the connection is not established. Repeat the procedure, moving closer to the router.
After successful pairing, the system will automatically assign an IP address to the device. Now you can install the drivers on your computer, selecting the "Wireless" connection type during installation, and the system will automatically detect HP Deskjet 3525 online.
Setup via a computer using a USB cable
The classic method guarantees the transfer of all necessary network parameters from the computer to the printer. For this, you'll need a driver. HP Smart or the full software package from the official website. First, connect the MFP to your computer via USB cable, even if you ultimately plan to use it wirelessly.
Run the setup file and follow the wizard's instructions. When prompted for a connection type, select "Wireless Connection." The installer will automatically switch the device to setup mode and transfer your network information. SSID and password.
☑️ Installation Preparation Checklist
During the installation process, the program will ask you to disconnect the USB cable. Do this only when explicitly instructed to do so by the installation wizard. After disconnecting the cable, the printer will attempt to connect to the network automatically using the transferred data. Wireless should be lit steadily.
| Setup stage | User action | Indicator reaction |
|---|---|---|
| Starting the installation | Running the setup.exe file | It's on constantly |
| Select type | Select "Wireless" | Flashing |
| Data transfer | Standby (via USB) | Flashing |
| Conclusion | Disconnecting USB | It's on constantly |
If the indicator starts flashing again after disconnecting the cable, the settings transfer was unsuccessful. In this case, repeat the procedure, ensuring that your antivirus or firewall isn't blocking the installer.
Direct connection via the control panel menu
Model HP Deskjet Ink Advantage 3525 Allows you to configure your network directly using the buttons on the device, without using a computer. This is convenient if you don't have a PC or cable handy. You'll need to know the exact name of your network and the password.
Press and hold the button Wireless (wireless) for 5 seconds until the indicator starts flashing. Then press the button Right arrow or use the button combination specified in the instructions to enter the setup menu (often this is pressing the wireless button and the cancel button at the same time).
After activating setup mode, a hotspot will be created on the printer. Connect to it from your phone or laptop (the network name will include "HP" and the device model). Open your browser; it will automatically redirect you to the page Embedded Web Server (EWS).
⚠️ Note: When connecting to the printer's hotspot, your phone will lose internet access. This is normal. After completing setup, remember to switch back to your main Wi-Fi network.
On the settings page, go to the section Networking -> Wireless -> Wireless Setup WizardSelect your home network from the list and enter the password. The printer will apply the settings and attempt to connect.
What should I do if the keyboard doesn't appear on the screen?
Sometimes the browser stores an old version of the EWS page. Try opening the settings page in incognito mode or clearing your browser's cache before entering your password.
Mobile setup via the HP Smart app
The most modern and convenient method for smartphone users. Download the app HP Smart from the App Store or Google Play. Make sure your phone is connected to the same Wi-Fi network you want to use for the printer.
Launch the app and tap "Add Printer" or the "+" icon. The app will begin searching for devices. If the printer isn't yet configured, the app will prompt you to enter setup mode. Follow the prompts on your mobile device.
- 📱 The application automatically calculates the data of your current Wi-Fi network.
- 🔑 You won't need to manually enter your password if you allow the app to access your location and network.
- ✅ Once setup is complete, the app will prompt you to scan a test page.
This method is especially effective because the application HP Smart The app automatically checks for firmware compatibility and up-to-dateness. If a firmware update is required, the app will notify you and prompt you to perform the update.
Diagnosing problems and resetting network settings
If none of the methods helped and the indicator continues to flash, you need to perform network resetThis will reset the network module to factory settings. Press and hold the buttons simultaneously. Wireless And Cancel (Cancel) for 3-5 seconds until the power indicator flashes.
A common issue is the incorrect frequency range. The 3525 series printers only operate within the frequency range. 2.4 GHzIf your router only broadcasts 5 GHz or uses a complex encryption type (such as pure WPA3), your device may not see the network. Try temporarily changing your router settings to WPA2-PSK (AES).
Also check if MAC address filtering is enabled on your router. If this feature is enabled, you'll need to add the printer's MAC address (found on the label on the back of the device or in the configuration report) to the list of allowed addresses.
Frequently Asked Questions (FAQ)
Can the HP 3525 be connected to a hidden Wi-Fi network?
Yes, it is possible, but only through the menu. Wireless Setup Wizard or software on a PC. Hidden networks are not displayed automatically; you'll need to enter the SSID manually.
The printer sees the network but won't connect. What's wrong?
Most likely, the password is incorrect or an unsupported encryption type is being used. Also, check if the DHCP table on your router is full (the limit on connected devices).
How to find out the printer's IP address after setup?
Press the wireless button and the information button (the "i" icon) at the same time. The printer will print a page where the section IPv4 Address The current address will be indicated.
Does Wi-Fi Direct work on this model?
Yes, the 3525 model supports Wi-Fi Direct. To enable it, press the Wi-Fi Direct button on the control panel. This allows you to print without a router, connecting directly to the printer's signal.