Modern technologies allow you to forget about bulky cables and inconvenient placement of equipment in your apartment. Wireless connection Provides access to printing documents and photos from any device in the home, be it a smartphone, tablet, or laptop. Model Epson L355 is one of the most popular representatives of the Printing Factory line, and its correct configuration will guarantee comfortable work for many years.
The process of integrating a device into a home network may seem complicated only at first glance. In reality, Wi-Fi protocol Provides stable data transfer if you follow a specific procedure. In this article, we'll cover all the details, from preparing the equipment to the intricacies of WPS setup and manual parameter entry.
Before you begin, make sure your router is working properly and is distributing internet. Epson MFP It doesn't have its own screen for entering passwords, so accuracy when typing on a computer or smartphone is critical. For successful initial setup, the computer and printer must be within the same Wi-Fi signal range of the router.
Equipment preparation and compatibility testing
You should start with a basic check of the technical condition of all system components. Make sure that printer The unit is plugged in and the cartridges are filled with ink. The control panel lights should be steady, not flashing red, which would indicate an ink supply error or paper jam.
The second important step is to check your router. For proper operation Epson L355 The router must support WPA/WPA2 security standards. Older WEP encryption methods may not be supported or may be unstable. Also, make sure you know the exact name of your network (SSID) and its password, as you'll need to enter them in the settings.
- 📶 Check that the router is turned on and the Wi-Fi indicator is active.
- 🖨️ Make sure the printer has cartridges installed and all shipping tapes have been removed.
- 💻 Prepare the computer or smartphone from which you will perform the setup.
If you are using a laptop, temporarily disable any VPN connections or third-party firewalls that may be blocking the discovery of network devices. Local area network must be open for data exchange. Corporate networks may have additional restrictions, so it's best to use a guest network or a personal router for home printing.
☑️ Ready to customize
Resetting network settings on an Epson L355 printer
If the device was previously used with a different router or the settings were reset, a full reset of the network settings is required. This action will restore network module Reset the printer to its factory defaults by clearing old connection profiles. Ignoring this step often results in the new device not recognizing the old printer.
To reset the printer, locate the Wi-Fi antenna button on the control panel. Press and hold it together with the Cancel button (the triangle in a circle) for a few seconds. The Wi-Fi and Wi-Fi Direct lights should begin flashing alternately, after which the printer will reboot the network module.
⚠️ Attention: After resetting your settings, all previously saved Wi-Fi passwords will be deleted from your device's memory. You'll need to re-enter your passwords to connect to your hotspot.
After rebooting, the lights should turn green, indicating that the device is ready to search for a network. If the blinking continues for too long, try turning it off and on again. MFP again. Sometimes the module needs time to fully initialize after software failures.
What to do if the indicators are flashing red?
If the indicators remain red or flash in emergency mode after the reset, check the ink levels. In some Epson models, low ink levels disable network functions to protect the print head. Refill the appropriate ink tanks and repeat the reset procedure.
Connection method via WPS (Wi-Fi Protected Setup)
The fastest way to establish a connection between your router and printer is to use WPS technology. This method allows you to automatically transmit a password, eliminating the need to manually enter complex characters. router must support this function (usually this is a separate button on the body or an option in the web interface).
Press the WPS button on your router. Hold it for 2-3 seconds until the WPS indicator starts flashing. Immediately after, within two minutes, press and hold the Wi-Fi button on the printer's control panel. Epson L355 until the indicators start flashing alternately.
The device will automatically find the network and establish a connection. This process takes between 30 seconds and 2 minutes. If successful, the Wi-Fi indicator on the printer will turn solid green. This means IP address received and the device is ready for use.
Manual setup via Epson iPrint or driver
If the automatic method doesn't work, you'll have to use a software solution. Download and install the utility. Epson iPrint on your computer or smartphone, or use the full driver package from the official website. Launch the program and select "Add a printer" or "Setup via USB."
The program will prompt you to temporarily connect the printer to your computer via a USB cable to transfer network settings. This is a secure method, as it eliminates the risk of password errors. Follow the on-screen instructions: select your network from the list, enter the password, and wait for confirmation.
| Method | Necessary equipment | Complexity | Setup time |
|---|---|---|---|
| WPS | Router with a WPS button | Low | 1-2 minutes |
| USB cable | USB Type-B cable | Average | 5-10 minutes |
| Wi-Fi Direct | Smartphone/PC | High | 10-15 minutes |
| EpsonNet Config | PC on the same network | High | 10-20 minutes |
After the settings have been successfully transferred, the program will prompt you to disconnect the USB cable. From this point on seal will be carried out over the air. Make sure your model appears in the list of available printers in your operating system with the "Ready" status.
Using Wi-Fi Direct technology
Function Wi-Fi Direct Allows you to connect devices directly to the printer without a router. This is ideal for printing from a smartphone when visiting someone or in an office where access to the main Wi-Fi network is limited. The printer creates its own access point to which your device connects.
To activate the mode, press the Wi-Fi Direct button on the panel Epson L355If this feature is enabled for the first time, you may need to reset the settings. After activation, print a network configuration sheet (while holding the Cancel button) to find the network name and password for connection.
On your smartphone or laptop, find the new network in the list of available Wi-Fi connections. It will have a name similar to DIRECT-xx-EPSON L355Enter the password specified in the manual or on the printed configuration sheet. You can now print documents.
⚠️ Attention: When connecting via Wi-Fi Direct, your mobile device may lose internet access because it switches to the printer's local network. To access the global network, you'll need to manually switch between networks.
Installing drivers and software
Even if the printer is visible on the network, the correct settings are required for full functionality. driversWindows or macOS operating systems can install a basic driver, but it won't provide access to all scanning and maintenance features. Use the official Epson website to download the full software package.
During the installation process, select the "Network" or "Wireless" connection type. The installer will find the device on the local network using its IP address. If the automatic search fails, you can enter the IP address manually, which can be found by printing a network status report.
It's also recommended to install ink level monitoring utilities. These allow you to track consumption and promptly order consumables. CISS systemThe cartridge installed in the L355 model requires the use of genuine ink to maintain the warranty and print quality.
Diagnostics and solution
Sometimes the setup process doesn't go smoothly. If the printer isn't found on the network, check if your antivirus software is blocking network discovery. Also, make sure the computer and printer are on the same subnet (e.g., 192.168.1.x). Different subnets can occur when using range extenders or guest networks.
A common problem is that the router's IP address changes every time it reboots. To avoid this, reserve a static IP address for your router. MFP In the router settings, bind it to the device's MAC address. This will prevent the connection from being lost and the printer from being lost by the system.
- 🔍 Check if the Wi-Fi indicator is green (not blinking).
- 🔄 Restart your router and printer one by one.
- 🛡️ Temporarily disable Windows Firewall to test.
If all else fails, reset the printer's network settings again and try the WPS method. In rare cases, the issue may be due to incompatibility with the router's security standards. Try temporarily changing the router's encryption type to WPA2-PSK (AES).
Why doesn't the Epson L355 printer detect the 5 GHz network?
The L355 model only supports the 802.11 b/g/n standard, which operates in the 2.4 GHz band. If your router only broadcasts the 5 GHz band or combines them into one with a 5 GHz priority, the printer may not see the network. Enable a separate guest network or the primary 2.4 GHz band in your router settings.
How to find out the IP address of a printer?
Press and hold the Network button (globe or antenna icon) on the printer control panel for 10 seconds. The printer will print a network status report, with the current IP address listed in the TCP/IP section.
Is it possible to connect a printer to a hidden network (Hidden SSID)?
Connecting to hidden networks is possible, but requires using the EpsonNet Config utility or a USB cable for initial setup, as the automatic network search will not detect a hidden SSID.