Connecting a Strizh TV to Wi-Fi: 4 Proven Methods + Troubleshooting

Televisions Strizh (production JSC "Horizon") have long gained popularity thanks to their combination of affordable price and modern features. But even with smart TVs Android TV or Linux firmware Users often face the problem of how to properly connect to their home Wi-Fi network, especially when it comes to models without an Ethernet port or with a non-standard menu interface.

In this article you will find 4 working connection methods — from standard password entry to bypassing blocking through ADBWe will analyze typical mistakes (for example, IP conflict or Authentication failed), we'll provide a diagnostic checklist and show you how to connect even without the original remote. And at the end, we'll include an FAQ with answers to the most frequently asked questions.

If your Strizh released before 2020, please note: some models (eg Strizh 32L5000T2SM or Strizh 43U6100T2SM) require a preliminary firmware update for stable operation with modern routers at a frequency 5 GHzMore on this in the section on router settings.

1. Standard connection via the settings menu

The most obvious way is to use the built-in TV menu. This works for most models. Strizh, except for the oldest ones (pre-2018). The interface may differ slightly depending on the firmware, but the general layout is the same.

To get started:

1. Turn on the TV and press the button Menu (or Home on remote controls with a touch panel).
2. Go to the section Settings → Network → Wireless network (Wi-Fi).
3. Select your network from the list. If it's not there, click Refresh the list or Search for networks.
4. Enter your Wi-Fi password. Use the virtual keyboard on the screen (controls: arrow keys on the remote).

⚠️ Attention: On models Strizh with firmware Linux (For example, Strizh 32L5000T2) The keyboard may take up to 10 seconds to appear. Do not press the keys repeatedly, as this will result in input failure.

After entering the password, the TV should automatically receive an IP address. If this does not happen:

• 🔄 Reboot your router (turn off the power for 30 seconds).
• 📶 Check the network operating mode: some models Strizh do not support 802.11ac (Wi-Fi 5). Switch the router to mode 802.11n (Wi-Fi 4) via web interface.
• 🔒 Make sure the password is entered correctly.Uppercase and lowercase characters are different!

Check that the router is turned on and distributing Wi-Fi|

Make sure the TV is within the network coverage area (no further than 10 meters from the router)|

Disable VPN or proxy on your router (if using one)|

Write down your Wi-Fi password on paper (to avoid mistakes when entering it)

-->

2. Connect via WPS (if the router supports it)

Function WPS (Wi-Fi Protected Setup) allows you to connect to the network without entering a password—just press a button on the router. This is convenient if you have a long, complex password or the virtual keyboard on your TV isn't working.

Instructions for Strizh:

1. On your TV remote, go to Settings → Network → Wi-Fi → WPS.
2. Select an option Connection via PBC (Push Button Configuration).
3. For 2 minutes press the physical button WPS on the back panel of the router (usually it is labeled or marked with an icon 🔄).
4. Wait for the message Connected on the TV screen.

⚠️ Attention: Some routers (eg. TP-Link Archer C6) disable WPS after 5 unsuccessful connection attempts. To unlock the feature, reboot the router.

If WPS does not work:

• 🔌 Check if the WPS function is enabled in the router settings (section Wireless Mode → WPS).
• ⏱️ Make sure you press the WPS button on your router within 120 seconds of activating the search on your TV.
• 📡 Try reducing the distance between your TV and router—sometimes WPS doesn't work over long distances.

3. Connecting via the app (for Android TV)

Models Strizh at the base Android TV (For example, Strizh 50U7400T2SM or Strizh 55U7500T2SM) support connection via a mobile application Google Home or TV Remote ControlThis is convenient if you:

• 📱 No original remote control (you use your smartphone as a remote control).
• 🔠 The virtual keyboard on the TV is broken.
• 🔒 You need to connect to a hidden network (SSID is not broadcast).

Step-by-step instructions:

1. Download the app Google Home (for Android TV) or TV Remote Control (for Linux firmware) from Google Play or App Store.
2. Make sure your smartphone and TV are connected to the same network (for example, via mobile Internet with Wi-Fi sharing).
3. Open the app and select your TV from the list of devices.
4. Go to the section Settings → Wi-Fi and follow the instructions on the screen.

⚠️ Attention: When connecting via Google Home The TV may ask for confirmation on the screen (a 4-digit code). If the code is not displayed, check if the mode is enabled. HDMI-CEC in TV settings (Settings → System → HDMI Control).

If the TV is not in the app:

• 🔄 Restart your TV (unplug it for 1 minute).
• 📶 Make sure your smartphone and TV are on the same network (even if it's a mobile hotspot).
• 🔧 Update your TV's firmware (instructions in the next section).

What should I do if the app doesn't detect the TV?

If Google Home does not detect yours Strizh, try:

1. Manually add the device by IP address (find it in the router settings in the DHCP section).

2. Use an alternative application, such as TV Remote Control by Twinone - It works better with older models.

3. Reset network settings on TV: Settings → Network → Reset network settings.

4. Connection without a remote control (alternative methods)

If your remote control is lost or broken, you can still connect to Wi-Fi. Here are three working methods:

Method 1: Buttons on the TV body

On the back or side panel of the TV Strizh there are physical buttons (usually Menu, Volume, Channel). With their help you can:

1. Click Menu and with the help of Volume +/- navigate through the items.
2. Choose Settings → Network → Wi-Fi.
3. Connect to the network using Channel +/- to enter the password.

Method 2: USB keyboard or mouse

Many models Strizh (especially on Android TV) support connecting USB devices. Connect the keyboard to the port. USB on TV and:

• 🖱️ Use your mouse to navigate the menu.
• ⌨️ Enter your password using a physical keyboard (much more convenient than a virtual one).

Method 3: ADB commands (for advanced users)

If you have access to Android TV through ADB (for example, via Ethernet or an OTG cable), you can connect to Wi-Fi using the command:

adb shell am start -a android.settings.WIFI_SETTINGS

This will open the Wi-Fi menu where you can enter your network details.

⚠️ Attention: Usage ADB requires USB debugging to be enabled (Settings → Developer options → USB debugging). If this mode is disabled, it will not be possible to activate it without the remote control.

5. Configuring the router for a stable connection

Sometimes the problem isn't with the TV, but with the router. Especially if you have:

• 📶 Dual-band Wi-Fi (2.4 GHz And 5 GHz),
• 🔒 Complex password with Cyrillic or special characters,
• 🛡️ MAC address filter is enabled.

What can be done:

🔹 Critical information: If your router uses WPA3, and the TV Strizh released before 2021, you won't be able to connect. Switch the network to WPA2-PSK (in the router's wireless network settings).

To change router settings:

1. Open your browser and enter the router's IP address (usually 192.168.0.1 or 192.168.1.1).
2. Log in (default logins: admin/admin or see the sticker on the router).
3. Go to the section Wireless network or Wi-Fi.
4. Change the parameters according to the table above and save the settings.

6. Common mistakes and their solutions

Even after entering the correct password, the TV Strizh may produce errors. Here are the most common ones and how to fix them:

• 🚫 Error: "No internet connection"
  Cause: The TV is connected to Wi-Fi but does not receive an IP address.
  Solution: Enable it in your router settings. DHCP or assign a static IP for TV.
• ⚠️ Error: "Authentication failed"
  Cause: Incorrect password, incompatible encryption type, or MAC address filter.
  Solution: Check the password, switch the router to WPA2-PSK, disable the MAC filter.
• 🔄 Error: "Obtaining IP address..." (hangs indefinitely)
  Cause: IP conflict or router DHCP server failure.
  Solution: Reboot the router, manually set the IP on the TV (for example, 192.168.0.100).
• 📵 Error: "Network out of range"
  Cause: The TV does not support 5 GHz or the signal is too weak.
  Solution: Switch the router to 2.4 GHz or move the TV closer to the router.

If the error persists, try reset network settings on TV:

1. Go to Settings → Network.
2. Select Reset network settings or Restore network settings to factory defaults.
3. Restart your TV and try connecting again.

What should I do if my TV doesn't respond to the remote control?

If the remote control does not work, check:

1. Batteries (replace with new ones).

2. Infrared receiver on TV (is it covered by a decorative panel?)

3. Remote control compatibility (some universal remote controls do not support Strizh).

If the remote control is broken, use the buttons on the TV body or connect a USB keyboard.

7. Update firmware for better compatibility

If your TV Strizh If your iPhone was released before 2020, the cause of Wi-Fi problems may be due to outdated firmware. This is especially true for models based on Linux, which did not initially support modern safety standards (WPA3, 802.11ac).

How to update firmware:

1. Download the latest firmware version from official website of Strizh (section "Support").
2. Copy the firmware file (usually with the extension .bin or .img) onto a flash drive formatted in FAT32.
3. Insert the flash drive into the USB port of the TV.
4. Go to Settings → Software Update → Local Update and select the file.
5. Wait until the process is complete (TV will reboot automatically).

⚠️ Attention: Don't turn off your TV during the update! If the process is interrupted, your TV may not turn on. In this case, you'll need to flash the firmware via UART (only in the service center).

After update:

• 🔄 Restart your TV.
• 📋 Check your firmware version in Settings → About TV.
• 🔧 Try connecting to Wi-Fi again.

If there is no firmware for your model on the website, please contact support. Strizh indicating:

• 📺 TV models (located on the sticker on the back).
• 🔢 Serial number.
• 📡 Current firmware version.

FAQ: Frequently asked questions about connection Strizh to Wi-Fi

🔹 Why can't my TV see my Wi-Fi network?

Possible reasons:

• The network operates in the range 5 GHz, and yours Strizh supports only 2.4 GHz.
• The router mode is disabled 802.11n (enable it in settings).
• The network is hidden (the SSID isn't broadcast). In this case, connect through the app or enter the network name manually.

🔹 How to connect to a hidden Wi-Fi network?

If your network is not broadcasting a name (SSID), try the following:

1. From your TV's Wi-Fi menu, select Add a network manually.
2. Enter the network name (SSID) and password.
3. Please specify the security type (WPA2-PSK or another).

On models with Android TV you can use the app Google Home to connect to hidden networks.

🔹 My TV connects to Wi-Fi, but the internet isn't working. What should I do?

Check:

• Settings DNS on TV (try to specify 8.8.8.8 And 8.8.4.4 manually).
• Internet operation on other devices (possibly a problem with the provider).
• Router settings: disable MAC address filtering And Parental control.

🔹 Is it possible to connect? Strizh to Wi-Fi without a password?

Yes, if your router supports it. guest network without password or mode WPS. You can also:

• Temporarily disable the password in the router settings (not recommended for security reasons).
• Use WPS (if the function is enabled).

⚠️ Attention: Open networks are vulnerable to hacking. Once you connect your TV, turn your protection back on.

🔹 How to reset network settings on Strizh, if nothing helps?

Perform a full network reset:

1. Go to Settings → Network.
2. Select Reset network settings or Restore network settings to factory defaults.
3. Confirm the action (you may be asked to enter your PIN, by default 0000 or 1234).

After the reset, the TV will forget all saved networks and you will be able to connect again.