Modern office equipment requires flexibility, and Epson L355 is no exception. This multifunctional device allows you to print, scan, and copy documents, but its main advantage is its wireless operation. Connecting the device to your home network allows you to print from mobile devices and work from multiple computers in the office.
The setup process may seem complicated at first glance. In fact, there are several proven ways to activate wireless module, each suited to specific operating conditions. We'll explore the most effective methods that guarantee a stable connection.
Before proceeding with the software, you need to check the physical condition of the equipment. Make sure the cartridges are refilled, and the device is plugged in and within range of a strong router signal. This is a basic requirement, without which further steps will be useless.
Preparing equipment and checking router settings
The first step is to check that your router is compatible with the security protocols supported by your printer. Epson L355 works correctly with encryption standards WPA2-PSK (AES) And WPA/WPA2If the router has outdated or very new protocols installed, the device may simply not see them.
It's also important to know your network name (SSID) and password. Most home networks hide the name, but the password must be entered correctly, taking into account the case of the letters. Even a single character error will cause the Wi-Fi indicator to flash, but no connection will occur.
⚠️ Important: If your router broadcasts two networks (2.4 GHz and 5 GHz) under the same name, the printer may attempt to connect to the 5 GHz band, which it does not support. We recommend temporarily separating the networks or forcing the printer to connect to 2.4 GHz.
Make sure that filtering is not activated on your router. MAC addressesIf this feature is enabled, you will need to find your printer's unique address (usually on a sticker on the back) and add it to the whitelist of allowed devices in your router settings.
Connection method via WPS button
The fastest way to connect is through technology. WPS (Wi-Fi Protected Setup)This method is ideal if you don't want to mess around with entering passwords and searching for networks in menus. However, it requires your router to also support this feature and have a corresponding physical or software button.
To begin, press the WPS button on your router. Hold it down for a few seconds until the security light starts flashing. After that, you have about two minutes to activate discovery mode on the printer itself.
- 📡 Press and hold the Wi-Fi button on the printer control panel for about 3 seconds.
- 🔄 The Wi-Fi and network indicators will start flashing alternately, indicating that the device is searching for a signal.
- ✅ When the indicators light up continuously, the connection is established successfully.
If automatic pairing doesn't occur the first time, try repeating the process while moving closer to the router. Sometimes interference from household appliances can interrupt the initial handshake between devices.
Using the WPS Pin code for secure pairing
In some cases, especially in corporate networks or on routers from certain providers, it is necessary to enter a special PIN codeThis code is generated by the printer itself and serves as a one-time key for network authorization without entering the main Wi-Fi password.
To get the code, press and hold the Wi-Fi button on your device until the network light turns on. Then press the button with the network icon (usually next to the Wi-Fi button). The printer will automatically print a network status report sheet, which will show your password. WPS Pin Code.
Enter this eight-digit code into your router's interface. This is usually done through the router's web interface under "Wireless" -> "WPS." After entering the code, the router will automatically transfer the necessary security settings to the printer.
What to do if the code is not accepted?
The WPS PIN code is only valid for a short time (usually 2-5 minutes). If you don't have time to enter it into your router settings, you'll need to repeat the code generation process on the printer. The old code is immediately invalidated by the security system.
This method is considered more secure, as it eliminates the risk of unauthorized access to the Wi-Fi network's master password during setup. However, it requires physical access to the router's control panel.
Setup via USB cable and Epson Net Setup utility
If wireless methods don't work or you want to set a static IP address, use the wired method. You'll need a computer with the driver installed and a USB Type AB (printer) cable. This method is the most reliable for initial configuration.
Run the installation disk or download the driver package from the official website. Select the "Wireless" connection type and follow the installation wizard's instructions. When prompted to connect the cable, connect the computer and printer.
☑️ USB Setup Preparation Checklist
During the installation process the utility Epson Net Setup The printer will automatically copy the wireless network settings from your computer to the printer. Once the process is complete, you can disconnect the cable—the device will continue to operate autonomously.
It's important to note that when using this method, the printer adopts the same security settings as your computer. If your PC has a complex corporate certificate, it will also be written to the MFP's memory.
Comparison of connection methods and troubleshooting
Each of the methods discussed has its own advantages and disadvantages depending on your infrastructure. Below is a table to help you choose the best option for your situation.
| Method | Complexity | Speed | Requirements |
|---|---|---|---|
| WPS (Push Button) | Low | High | Router support |
| WPS Pin | Average | Average | Access to the router admin panel |
| USB cable | High | Low | Availability of a PC and cable |
| Epson iPrint | Low | High | Smartphone with Android/iOS |
A common issue is when the Wi-Fi indicator is on, but printing does not work. This could indicate a conflict. IP addressesTry rebooting your router so that it assigns a new address to the printer in the DHCP pool.
Mobile printing and additional features
Once you've successfully connected Wi-Fi to your Epson L355 printer, your capabilities are significantly expanded. You can use the app Epson iPrint to print photos directly from your phone or tablet without using a computer.
The app also lets you scan documents directly to cloud storage services like Google Drive or Dropbox. Simply scan the document through the app interface, and it will automatically upload to your account.
In addition, the technology is supported Epson Print Enabler For Android devices, this allows you to print from most apps without installing additional software. Simply select "Print" from the menu of any document or photo.
⚠️ Note: The mobile app interface and functionality may be updated by the developer. If you don't see a menu item, check for updates to the Epson iPrint app in the Google Play Store or App Store.
Remember that for mobile features to work, your smartphone and printer must be on the same subnet. If you have a guest Wi-Fi network set up, connect both devices to it to ensure they are visible to each other.
In conclusion, setting up a wireless connection correctly will free you from unnecessary cables and make working with documents much more convenient. Choose the appropriate method, follow the instructions, and your printer will work reliably.
Why doesn't my Epson L355 printer see my Wi-Fi network?
The most common issue is frequency band. The L355 model only operates in the 2.4 GHz band. If your router only broadcasts in the 5 GHz band or hides the network name (SSID Broadcast disabled), the printer won't detect it. Also, check if a MAC address filter is enabled.
How to change the printer IP address after setup?
To change the IP address, you must use the Epson Net Config utility. Launch the program on a computer connected to the same network, find the device in the list, go to TCP/IP properties, and manually set a static address.
Is it possible to connect Epson L355 to a hidden network?
Yes, but only by manual setup using a USB cable and the Epson Net Setup utility. This method allows you to manually enter the hidden network's SSID and security settings, as automatic network discovery won't detect them.
The Wi-Fi light is orange, what does it mean?
An orange light usually indicates a connection error or low signal strength. Check the password you entered, make sure the printer is not too far from the router, and try reconnecting the device.