How to access the internet on an LG TV via Wi-Fi: complete instructions using the remote control

Modern Smart TV from LG allow you to access the Internet without additional devices - just connect to Wi-Fi and use the built-in browser or apps. However, many users encounter difficulties: the network can't be found, the password isn't accepted, or the browser won't open. This article will help you figure out how to properly set up the Internet on your TV. LG any model (from webOS 3.5 to webOS 24) by using only remote control, without a keyboard or mouse.

We will cover not only the basic steps of connecting to Wi-Fi, but also the nuances of working with the browser, solving typical errors (for example, IP conflict or limited access), as well as alternative ways to access the network if the standard method doesn't work. We'll pay special attention to models LG OLED, NanoCell And QNED, where the interface may differ.

If your TV was released before 2018, some features (such as support Wi-Fi 6 (or modern browser versions) may be missing. In this case, check the firmware update in the menu. Settings → Support → Software Update.

1. Preparing your LG TV for Wi-Fi connection

Before connecting your TV to the Internet, make sure three key conditions are met:

• 📶 The router is turned on and distributes Wi-Fi (the network indicator lights up green/blue). If you use 5 GHz, check if your model supports it LG (in budget series it can only work 2.4 GHz).
• 🔋 The TV is connected to the power supply. and is not in power saving mode. On some models, when the remote control battery is low (CR2032) Wi-Fi connection may be interrupted.
• 📱 You have login information for the network: network name (SSID) and password. If the password is lost, you can find it on the router's sticker or in your provider's personal account.

If your TV was previously connected to a different network, it's best to clear the old settings. To do this:

1. Open Settings → Network → Wi-Fi Connections.
2. Select the saved network and press Delete (or Forget in new versions webOS).
3. Confirm the action with the button OK on the remote control.

⚠️ Attention: On TVs LG With webOS 4.0 On devices older than this, a reboot may be required when resetting networks. Don't interrupt the process if the screen goes black for 10-15 seconds—this is normal.

If you use guest Wi-Fi (for example, in a hotel or cafe), make sure the network doesn't require browser authentication. If this is the case, additional configuration will be required—we'll cover this in the troubleshooting section.

2. Step-by-step instructions: how to connect LG Smart TV to Wi-Fi using the remote control

The process of connecting to a wireless network on all TVs LG similar, but may differ slightly depending on the version webOSWe will consider a universal algorithm that works on 90% of models (2018-2026).

More details about each step:

1. Open the settings menu.
   

   Click the button ⚙️ Settings (or Home → Settings on the remote controls Magic Remote). In older models the path may look like this Menu → All Settings.

2. Go to the network section.
   

   Select Network → Connect to Wi-FiIf the TV has not previously connected to the Internet, the system may prompt you to select a connection type - select Wireless network.

3. Select your network.
   

   Find yours in the list of available networks. SSIDIf the network is not listed, click Refresh or check if it is hidden (in this case, you will need to enter the network name manually).

4. Enter your password.
   

   Use on-screen keyboard and a remote control for entering the password. Please note:

   • 🔤 Case sensitive: Password And password - different passwords.
   • 🔢 To switch between letters and numbers, use the button 123/Symbols on the keyboard.
   • 🖱️ On the remotes Magic Remote You can use the pointer like a mouse for convenient input.

Confirm the connection.

After entering the password, select Connect or ReadyThe TV will check the connection and assign IP addressIf an error occurs, check your password or reboot your router.

On models with webOS 6.0 and newer, after connecting, a window may appear prompting you to update the software. We recommend agreeing to this—this will fix any potential Wi-Fi issues.

3. How to use the Internet on an LG TV: browser and apps

Once you have successfully connected to Wi-Fi, you can use the internet in two ways:

1. Via the built-in browser (available on all models with webOS).
2. Through applications (YouTube, Netflix, instant messengers, etc.).

Let's consider both options in more detail.

3.1. Working with the built-in browser

Browser on LG Smart TV it's called LG Web Browser (or simply Browser (in new versions). To open it:

1. Click the button Home on the remote control.
2. At the bottom of the screen, find the browser icon (usually a globe or logo) WWW).
3. Select a browser and wait for it to load.

Features of the browser on LG TV:

• 🔍 Supports voice search (microphone button on the remote control Magic Remote).
• 📱 You can sync bookmarks with your mobile browser via your account LG.
• ⚠️ Not all websites are displayed correctly due to restrictions webOS (for example, complex JavaScript applications).
• 🎮 For easy control, use Magic Remote as a pointer or connect a game controller.

If the browser does not open, check:

• Connect to the Internet (there should be a Wi-Fi icon in the upper right corner of the screen).
• Browser updates in LG Content Store.
• Parental control settings (sometimes the browser is blocked).

3.2. Using Internet applications

Most users prefer apps to browsers. LG Smart TV pre-installed:

• 🎬 YouTube, Netflix, Prime Video — for video streaming.
• 🎵 Spotify, Apple Music — for music.
• 💬 Zoom, Skype — for video calls (webcam required).
• 🎮 GeForce NOW, Xbox Cloud Gaming — for cloud gaming.

To install a new application:

1. Open LG Content Store (shopping bag icon).
2. Select a category (eg. Video or Games).
3. Find the desired application and click Install.

⚠️ Attention: On TVs with webOS 3.5-4.5 some applications (eg Disney+ or TikTok) may not be supported. Check compatibility on the website. LG.

4. Typical problems and their solutions

Even after connecting to Wi-Fi correctly, errors can still occur. We've compiled a list of the most common issues and how to fix them.

If your TV connects to Wi-Fi but your internet speed is very slow, try:

• 📡 Move the router closer to the TV (or use repeater).
• 🔄 Switch the Wi-Fi channel in the router settings (for example, from car on 6 or 11).
• 🔌 Connect your TV to your router via Ethernet cable (if there are ports).

What should I do if my LG TV won't connect to Wi-Fi at all?

If your TV can't detect any networks, the problem may be a hardware failure in the Wi-Fi module. Check:

1. Does Wi-Fi work on other devices (phone, laptop).

2. Is there any physical damage to the antenna (on the back of the TV).

3. Is the TV firmware updated (in the menu) Settings → Support → Software Update).

If nothing helps, contact a service center - the Wi-Fi module may need to be replaced.

5. Alternative ways to connect to the Internet

If connecting via Wi-Fi is not possible (for example, due to a weak signal or a faulty module), there are three alternative options:

5.1. Connecting via Ethernet cable

The most stable way is to use network cableTo do this:

1. Connect one end of the cable to the router and the other to the port LAN on TV.
2. On the menu Settings → Network select Wired network.
3. Wait for automatic setup IP.

Advantages:

• 🚀 Higher speed and stability.
• 🛡️ Less interference compared to Wi-Fi.

5.2. Using a USB modem (3G/4G)

Some models LG Smart TV (for example, series UN7300 or Nano85) support connection via USB modemTo do this:

1. Insert the modem into the port USB on TV.
2. Go to Settings → Network → Mobile network.
3. Select an operator and connect.

Please note:

• ⚠️ Not all modems are compatible - check the list of supported devices on the website LG.
• 💰 Traffic will be charged according to your mobile operator's rules.

5.3. Screen Mirroring (screen transfer from phone)

If you only need the Internet to view content, you can use screen mirroring from a smartphone:

• 📱 On Android: turn on Smart View or Google Cast.
• 🍎 On iPhone: use AirPlay (required) LG TV With webOS 5.0 and newer).

Disadvantages of the method:

• 📶 Video quality depends on Wi-Fi speed.
• 🔋 My phone's battery drains quickly.

6. Setting up parental controls and security

If children have access to the TV, it is recommended to set up parental controlThis will allow:

• 🔒 Block unwanted websites in your browser.
• 🎬 Restrict access to apps by age (for example, 18+).
• ⏰ Set time limits for use.

To enable parental controls:

1. Go to Settings → General → Security → Parental Controls.
2. Install PIN code (remember it or write it down!).
3. Set restrictions for your browser, apps, and purchases.

Additional security measures:

• 🔄 Update your TV firmware regularly (in the menu Settings → Support → Software Update).
• 🛡️ Turn it off Remote access in network settings if you don't use it.
• 🔑 Use a complex Wi-Fi password (at least 12 characters with letters and numbers).

⚠️ Attention: If you have forgotten your parental control PIN, it can only be reset by performing a full reset of your TV (Settings → Support → Factory reset). This will delete all data, including installed apps!

7. Optimizing Internet Speed ​​on LG Smart TV

Slow internet on TV is a common problem, especially when watching videos in 4K or HDRHere's how to improve speed:

7.1. Setting up a router for a TV

Optimal router parameters for LG Smart TV:

• 📶 Range: 2.4 GHz (for stability) or 5 GHz (for speed, if supported).
• 🔄 Channel: manually select the least loaded one (eg. 1, 6 or 11 For 2.4 GHz).
• 🔒 Encryption: WPA2-PSK (don't use outdated WEP).
• 📦 QoS: enable traffic prioritization for LG TV By MAC address.

7.2. Setting up your TV

On the menu LG Smart TV You can optimize network parameters:

1. Open Settings → Network → Additional settings.
2. Turn on Automatic IP acquisition (if disabled).
3. Turn it off Wi-Fi energy saving (may reduce speed).
4. In the section Network monitor Check your current connection speed.

For speed test:

1. Open your browser and go to speedtest.net.
2. Run the test and compare the results with the speed according to your provider's tariff.

If the speed is lower than expected:

• 🔌 Restart your router and TV.
• 📵 Make sure there are no sources of interference nearby (microwaves, cordless phones).
• 🔄 Update your router firmware (via the web interface, usually 192.168.1.1).

8. Frequently Asked Questions (FAQ)

🔹 Why won't my LG TV connect to Wi-Fi even though the password is correct?

Possible reasons:

• The router is using an incompatible encryption type (eg. WPA3 instead of WPA2). Try changing your router's security settings.
• Filter enabled MAC addresses on the router. Add MAC TV to the list of allowed devices.
• There's a problem with your TV's firmware. Please update the firmware in the menu. Settings → Support.

If nothing helps, reset the network settings on your TV: Settings → Network → Reset network settings.

🔹 Is it possible to connect an LG TV to Wi-Fi without a remote?

Yes, there are three ways:

1. Via the app LG ThinQ: Download it to your smartphone, connect to the same Wi-Fi network as your TV, and control your TV like a remote control.
2. Using the buttons on the TV: There is a button on the back panel JOYSTICK (or touch buttons) that you can use to open settings and connect to Wi-Fi.
3. Via HDMI-CEC: If the TV is connected to a device (e.g. Apple TV or Xbox), you can control it through the remote control of this device.

🔹 How do I find the MAC address of my LG TV to connect it to a router?

There are two ways to find a MAC address:

1. In the TV menu: Settings → General → About TV → Network Information.
2. On the sticker on the back of the TV (look for the line MAC Address or Wi-Fi MAC).

The MAC address looks like this 00:1A:2B:3C:4D:5E (12 characters separated by colons).

🔹 Why is YouTube slow on my LG TV even though my internet speed is fast?

Reasons for YouTube slowdowns LG Smart TV:

• Application cache: Clear YouTube data in Settings → General → Storage → YouTube → Clear Cache.
• Video resolution: In YouTube settings, limit the maximum quality to 1080p (4K may lag a bit).
• Background processes: Close other applications (eg. Netflix or browser) that may consume traffic.
• YouTube servers: Sometimes changing DNS helps 8.8.8.8 (Google) in the TV network settings.

🔹 Can I use a VPN on my LG TV to access blocked websites?

Yes, but with some reservations:

• Via browser: some VPN extensions (eg. Browsec) work in LG Web Browser, but they can slow down.
• Via router: It's more reliable to set up a VPN on your router—then all your TV traffic will go through the VPN.
• Via Smart DNS: services like Unlocator or Smart DNS Proxy allow you to unlock content without losing speed.

⚠️ Built-in VPN support in webOS is missing, so applications like Netflix or Disney+ may block access when a VPN is detected.