Owners of monochrome laser printers HP Laser 107w Often, we encounter a situation where we need to connect a new device to the network, but the default password has been lost or never written down. This model, like many modern office devices, uses technology Wi-Fi Direct For direct printing without a router. By default, the security system generates a unique access code that must be entered the first time you pair your smartphone or laptop.
There are several proven ways to restore access to your printer's wireless network settings. Methods These range from simply printing configuration reports to using specialized software. It's important to understand that this isn't a password for accessing the admin panel, but rather a security key for the wireless connection.
In some cases, if standard methods do not work, a full reset network settings to factory defaults. This action will restore the default password printed on the case label, which is often the quickest solution. Below, we'll detail each of the available options.
Printing a network configuration page
The most reliable and quick way to find out the current password for your wireless network is to print a special configuration report. In the model HP 107w This document contains comprehensive information about the status of the Wi-Fi module, IP address and, most importantly, the PIN code or password Wi-Fi DirectPhysical access to the printer control panel is required to perform this operation.
You'll need to perform a sequence of actions using the buttons on the device's body. Make sure there's paper in the tray and the printer is ready (green light). Pressing the key combination initiates the print job.
⚠️ Caution: If the printer is in deep sleep mode, briefly pressing the power button may not wake it up immediately. Wait until the indicator light turns solid green before attempting to print reports.
The procedure for printing a report is as follows:
- 🖨️ Press and hold the button
WPS(wireless network icon) for 10 seconds until the indicators start flashing. - 📄 Immediately after this, press the continue button (triangle in a circle) once.
- 📑 The printer will start printing the page where in the section Wi-Fi Direct a password will be indicated.
On the printed sheet, look for the line Wi-Fi Direct Password or PinThis is the character set you need to enter on your phone or computer when searching for a device. If the report shows the status as "Off," then the direct printing function is disabled and must be activated through the driver.
Using the HP Smart app to restore access
Modern print ecosystems such as HP Smart, allow you to manage security settings through a graphical interface on your smartphone or PC. If you already have one device connected to a printer, you can use it to view the network settings of another device. This is especially convenient when you need to connect a new laptop and don't have a printout handy.
The application scans the local network and finds connected devices. HP Laser 107wAfter authorization (which often happens automatically), in the settings menu you can find a section responsible for wireless connections. It may display the current status and the option to reset the password to a new one you set yourself.
Algorithm of actions in the application:
- 📲 Launch the app HP Smart on a device that already has access to the printer.
- ⚙️ Select your printer from the list and go to the "Printer Settings" or "Advanced Settings" section.
- 🔐 Find the "Network" or "Wi-Fi Direct" tab and look at the security key field.
Some firmware versions may hide direct password viewing for security reasons. In this case, the app will offer the "Change Password" option. New code will become known immediately after its installation, which will solve the problem of forgotten data.
Reset network settings to factory defaults
If none of these methods work, or if the printer was purchased second-hand and the previous owner changed the default settings, a hard reset is the only solution. This procedure returns the Wi-Fi module to its default state. After the reset, the password will be the one found on the sticker on the back or side of the device.
The reset process on the model HP 107w It's performed hardware-based, without requiring a computer connection. This makes the method universal, even when drivers aren't installed.
Instructions for performing a reset:
- Turn off the printer using the power button.
- Press and hold the button at the same time
Wi-Fiand the buttonCancel(cross). - Without releasing the button, turn on the printer.
- Keep the buttons pressed for about 10-15 seconds until all the indicators flash simultaneously.
After this procedure, the wireless network indicator will begin flashing blue, indicating setup mode. You can now use the default password from the label for the initial connection. universal solution for most access issues.
Connection via WPS technology
Protocol WPS (Wi-Fi Protected Setup) allows you to connect devices to the network without entering long passwords. If your router supports this feature (and most modern models do), you can connect HP 107w Connect to the internet with the press of a button. This eliminates the need to know or manually enter the Wi-Fi Direct password.
To implement this method, the router must have a physical WPS button or a corresponding function in the web interface. Printer HP 107w It also has a button to activate this mode. The connection between the devices is established automatically within two minutes.
Steps to connect:
- 📡 Press the WPS button on your wireless router.
- 🖨️ Press and hold the button for 2 minutes
Wi-Fion the printer about 3 seconds. - 🔄 Wait until the Wi-Fi indicator on the printer turns solid blue.
⚠️ Note: The WPS protocol is considered less secure than manually entering a complex password. If you use the printer in an office with high data security requirements, it's better to use the manual security key entry method.
Wireless network status indicator table
Understanding the LED signals your printer emits can help you diagnose connection issues. HP 107w Uses color indicators to indicate network status. Misinterpreting these signals can lead to the false conclusion that the password is invalid or the network is unavailable.
Below is a breakdown of the main wireless indicator states. Pay attention to the blinking pattern, as it often indicates a specific configuration error.
| Indicator color | Work schedule | Meaning |
|---|---|---|
| Blue (on) | Active | The printer is connected to a Wi-Fi network. |
| Blue (flashing) | Setup mode | Waiting for connection or resetting settings |
| Turned off | Not active | The wireless module is turned off |
| Orange (flashing) | Error | Connection problem or hardware failure |
Common password entry errors and their solutions
Even with the correct password, users often encounter device pairing failures. This can be due to human error or the system's inherent character recognition issues. Input errors account for more than 60% of all problems with connecting peripherals.
First, check your keyboard layout. Often, a Russian character is entered instead of a Latin letter, resulting in an incorrect password hash. Also, pay attention to the case: the system distinguishes between uppercase and lowercase characters.
Typical problems and solutions:
- 🔤 Symbol confusion: Number
0(zero) is often confused with the letterO, and the number1— with the letterlorICheck the label carefully. - 📏 Spaces: When copying a password from a document or message, accidentally adding a space at the beginning or end of a line will make the key invalid.
- 📶 Distance: If the device is far from the router, the signal may be interrupted during the password check, creating the illusion of an incorrect key.
Is it possible to change the Wi-Fi Direct password on an HP 107w printer?
Yes, you can change the default password. To do this, connect to the printer, launch the HP Smart app or web interface (EWS) via a browser, enter the device's IP address, go to network settings, and set a new PIN in the Wi-Fi Direct security section.
What if there is no password on the label?
If the sticker is damaged or missing, it's impossible to find the factory password. In this case, the only solution is to completely reset the printer's network settings (press the power-on button combination). After this, the device will use the default password generation algorithm or allow you to set a new password without knowing the old one.
Does the HP 107w work with 5GHz networks?
No, model HP Laser 107w equipped with a module that supports only the standard 802.11 b/g/n, which operates exclusively in the 2.4 GHz band. If your router only broadcasts on the 5 GHz band, the printer won't see it. You need to enable 2.4 GHz broadcasting in your router settings.
How many devices can be connected via Wi-Fi Direct?
Simultaneously to the printer's Wi-Fi Direct mode HP 107w Up to five devices can be connected. However, for stable operation and document printing, it is recommended to limit the number of active connections, as the channel throughput in this mode is lower than when connected via a router.