How to Change Wi-Fi on a Xiaomi Robot Vacuum: 3 Proven Methods

Robot vacuum cleaners Xiaomi Robot vacuums are among the most popular home cleaning tools, but their operation directly depends on a stable Wi-Fi connection. Changing your router, moving to a new apartment, or even simply changing your network password can turn into a headache if you don't know how to properly reset your connection. Unlike smartphones or laptops, where changing your network takes just a few clicks, with robot vacuums, the process is often hidden deep within a mobile app or requires manipulation of the device itself.

In this article we will look at All current methods for changing Wi-Fi on robotic vacuum cleaners Xiaomi (including models Mi Robot Vacuum-Mop 2 Pro, Dreame Bot Z10 Pro, Viomi V3 and others). You'll learn how to do this through the official app. Mi Home/Xiaomi Home, what to do if the robot doesn't see a new network, and how to avoid common errors that can cause the device to lose connection with servers. We'll pay special attention to hidden settings in firmware from 2023–2026, which are not documented in the official instructions.

1. Preparation: What to do before changing Wi-Fi

Before setting up, make sure you've completed the basic requirements. Ignoring these steps may cause the bot to malfunction or even become unlinked from your account. Xiaomi.

• 📱 Update the application Mi Home or Xiaomi Home to the latest version. Older versions (before 6.0) do not support new connection protocols.
• 🔄 Reboot the robot: Turn it off with the power button for 10 seconds, then turn it on again. This will reset the network settings cache.
• 📶 Check your router: Make sure the new network is in range 2.4 GHz (robots Xiaomi do not support 5 GHz!). Disable guest access and MAC address filtering.
• 🔋 Charging the robot: The battery level must be at least 30%. If the battery is low, the device may interrupt the setup process.

If you are changing your Wi-Fi due to a move, please note: some robot models (e.g. Dreame Bot L10 Pro) are linked to the account region XiaomiWhen changing countries, you may need factory reset — we will talk about this in the section on manual configuration.

⚠️ Attention: If your robot was previously connected to the network with Chinese firmware (for example, purchased on AliExpress (Without a global version), changing the Wi-Fi connection may block access to some features. In this case, a firmware update will be required.

2. Method 1: Change Wi-Fi via the Mi Home/Xiaomi Home app

This is the simplest and most recommended method, which works for 90% of models. The instructions are valid for apps of version 6.5.400 and newer (2026).

1. Open the app Mi Home or Xiaomi Home and go to the tab Devices.

2. Select your robot vacuum from the list. If the device is grayed out (offline), tap the three dots in the upper right corner and select Device Settings.

3. Scroll down to the section Wi-Fi network and press Change network (or Connect to another network in new versions).

4. The app will prompt you to select a new network from the list. Enter the password and wait for confirmation. The robot will beep and flash its indicator.

If the robot does not connect after these steps, check:

• 🔍 Does the robot see the new network (the Wi-Fi indicator on the body should flash blue).
• 📵 Is the router in the offline mode? WPA3 - some models Xiaomi support only WPA2-PSK.
• 🌐 Is your antivirus or firewall blocking the connection to the robot on your phone?

⚠️ Attention: In 2026 firmware for models Mi Robot Vacuum-Mop 2 Pro And Dreame Bot D9 A bug has appeared that causes cleaning schedules to reset when changing Wi-Fi. Save screenshots of settings before starting the procedure!

3. Method 2: Reset the network using the button on the case

If the robot does not respond to commands from the application or you have forgotten the password for the old network, you can do reset network settings manually. This method works for all models, including Viomi V2 And Xiaomi Mi Robot 1S.

Instructions:

1. Turn off the robot using the power button (hold for 3 seconds).

2. Press and hold the buttons simultaneously Home (Home) and Nutrition for 5-7 seconds until you hear a voice message in Chinese or English ("Wi-Fi reset"). On some models, instead of a voice alert, the indicator will flash orange indicator.

3. Release the buttons. The robot will automatically reboot and create its own access point with a name like Xiaomi_Vacuum_XXXX.

4. Connect to this network from your phone (the password is usually empty or 12345678) and re-add the robot to the application Mi Home like a new device.

This method is useful if:

• 🔄 The robot is stuck on the old Wi-Fi and doesn't respond to commands.
• 🔐 You don't remember the password for your previous network.
• 📱 The app is throwing an error."Failed to connect to the device".

What should I do if the robot does not make a sound when resetting?

On models without a speaker (for example, Xiaomi Mi Robot LiteA successful reset is indicated by the indicator flashing blue and red alternately. If the indicator doesn't respond, try holding the buttons for up to 10 seconds or plug the robot into the charger before resetting.

4. Method 3: Manual connection via the robot's access point

If the first two methods don't work, you can connect to the robot directly, like a router. This method is universal and works even with firmware errors.

Step-by-step instructions:

1. Perform a network reset (as in Method 2) to allow the robot to create its own access point.

2. On your phone, go to Wi-Fi settings and connect to the robot's network (the name starts with Xiaomi_, Viomi_ or Dreame_).

3. Open your browser and enter the address 192.168.4.1 or 192.168.8.1 (Depending on the model). The settings page should open.

4. Select your home network from the list, enter the password, and save the settings. The robot will reboot.

If the page does not open:

• 📱 Make sure your phone is not connected to mobile data (turn off 4G/5G).
• 🌐 Try a different browser (recommended) Chrome or Firefox).
• 🔄 Reboot the robot and try connecting again.

5. Common mistakes and their solutions

Even when following the instructions, users often encounter problems. We have collected TOP 5 mistakes and ways to fix them:

• 🚫 "Unable to connect to device" in the app Mi Home:

  Reason: IP address conflict or router blocking. Solution: Restart the router and the robot, then try again.

• 🔴 The indicator is flashing red after changing Wi-Fi:

  Reason: The robot cannot contact the servers. XiaomiSolution: Check if your antivirus is blocking access to domains. mi.com And xiaomi.net.

• 📡 The robot doesn't see the new network.:

  Reason: The router is operating in mode 802.11n Only or included WPA3Solution: Switch your router to mixed mode 802.11b/g/n and use WPA2-PSK.

• 🔄 After changing Wi-Fi, cleaning settings were reset:

  Cause: A bug in firmware versions from 2023–2026. Solution: Restore settings manually or roll back the firmware (if available).

• 📵 The app can't find the robot.:

  Reason: The robot is linked to a different account region. Solution: Change the region in the settings. Mi Home on"China" (for global models) or"Russia" (for official deliveries).

⚠️ Attention: If after changing Wi-Fi the robot stops responding to voice commands (for example, through Alice or Google Assistant), check if the account link has been reset. To do this, go to Device Settings → Account and log in again.

6. Features for different robot vacuum models

Not all robots Xiaomi They are configured identically. Below are the key differences between popular models:

For models Roborock (For example, S7 MaxV), which are also sold under the brand Xiaomi, a separate application is used RoborockThe instructions for changing Wi-Fi are similar, but the interface is different—look for the section Device Settings → Wi-Fi Network.

7. What to do if nothing helps?

If you've exhausted all other methods and the robot still hasn't connected to the new network, try the following steps:

1. Full reset to factory settings:

   Press and hold the button Nutrition for 15–20 seconds until you hear a long beep. The robot will return to its "out of the box" state and will need to be configured again.

2. Manual firmware update:

   Download the latest firmware for your model from the official website. Xiaomi (chapter"Support") and update the robot via a microSD card (instructions are in the device documentation).

3. Contacting support:

   If the robot is under warranty, contact the service center. Xiaomi via in-app chat Mi Home (chapter"Feedback"). Please attach screenshots of the errors and describe the steps you took.

In extreme cases, if the robot has completely stopped responding to settings, check:

• 🔌 power unit: There may be a fault in the charging station preventing it from working properly.
• 📡 Wi-Fi antenna: on some models (eg, Dreame Bot L10) the antenna may come off when dropped.
• 🛠️ Service center: If the robot does not turn on or does not respond to reset, the board needs to be diagnosed.

FAQ: Frequently asked questions about changing Wi-Fi on Xiaomi robot vacuums

Can a Xiaomi robot vacuum cleaner be connected to a 5GHz network?

No, all robot vacuum cleaners Xiaomi (including 2026 models) support networks only 2.4 GHzIf your router is running in dual-band mode, make sure that 2.4 GHz And 5 GHz are distributed among different names (SSIDs). Some routers (for example, Keenetic) by default they combine networks - this needs to be disabled in the settings.

Why does the robot connect to Wi-Fi, but the app shows "Offline"?

This is a problem for robots with Chinese firmware. Reasons:

• 🌍 The robot is tied to a Chinese server (cn), and your account is to the European one (ru or eu).
• 🔒 Traffic blocking by the provider (often happens with Rostelecom or Beeline).
• ⏳ Servers Xiaomi temporarily unavailable (check the status on the website) status.mi.com).

Solution: change your account region to Mi Home on"China" or connect to another region via VPN.

How do I change my Wi-Fi if I forgot my old network password?

In this case only this will help reset network settings (Method 2) If the robot was connected to a network with a unique name (for example, MyHome_5G), and you don't remember the password, try:

1. View the password in the router settings (section Wireless → Security).
2. Reset the router to factory settings (button Reset on the back panel).
3. Connect to the robot via its access point (Method 3).

Do I need to reflash the robot after changing the Wi-Fi?

No, reflashing the firmware is not required in 99% of cases. However, if the robot starts to malfunction after changing the network (for example, it doesn't create a map or doesn't respond to commands), check the firmware version in the app (Device Settings → About Device). If the version is older than 2023, update the software via Mi Home or manually.

Can I use the robot without Wi-Fi?

Yes, robot vacuum cleaners Xiaomi They work autonomously without an internet connection, but with limitations:

• ❌ There will be no remote control via the app.
• ❌ Cleaning history and room maps will not be saved.
• ❌ It is not possible to update the firmware.
• ✅ Basic functions will be retained: cleaning at the touch of a button, returning to the base, and obstacle avoidance.

Wi-Fi is required for full functionality.