Securing your home network begins with setting a strong access key, and for Infolink equipment owners, this process is a top priority. Many users neglect to change factory settings, leaving default combinations easily guessed by attackers. As a result, personal information becomes accessible to outsiders, and the internet connection can be used for illegal activities without the owner's knowledge.
The procedure for changing the password on routers Infolink It doesn't require deep technical knowledge, but it does require careful attention to interface details. Modern models support various encryption standards, such as WPA2-PSK and newer WPA3, which significantly increases the level of security for transmitted data. It's important to understand that changing the access key will disconnect all connected devices, requiring them to be reconnected.
In this article, we'll cover every setup step in detail, from physical connection to security verification. You'll learn how to avoid common configuration errors and what to do if the web interface stops responding. Proper Configuration wireless network — this is the foundation for the stable operation of all smart devices in your home.
⚠️ Note: Infolink router firmware interfaces may vary slightly depending on the software version and specific device model. If you don't find the menu item described, look for a similar section with a similar name or refer to the manufacturer's documentation.
Preparing for setup and entering the interface
Before making any changes to your router configuration, you need to ensure a stable connection between your computer or smartphone and the device itself. A wired connection via LAN cable, since when you change the WiFi password, the over-the-air connection will be interrupted, and you may lose access to the settings without completing the process.
To access the control panel, open any browser and enter the router's IP address in the address bar. By default, for most models Infolink the address is used 192.168.0.1 or 192.168.1.1If none of these are suitable, check the sticker on the bottom of the device—it contains the exact authorization information.
The system will ask for the administrator login and password. The default combination is often admin / admin, but if you've previously changed this data and forgotten it, a full factory reset will be required. Click the button Reset on the back of the device and hold it for about 10-15 seconds until the indicators blink.
☑️ Check before entry
Navigating the Wireless Network Menu
After successful authorization, you'll be taken to the main status page, which displays connection information and channel load. We're interested in the section responsible for wireless connections, usually called Wireless, WiFi Settings or "Wireless Mode".
Within this section, you need to find a subsection related to security. It may be called Wireless Security, "Security," or "Network Protection." This is where you'll find the encryption type settings and the field for entering a new password. Don't confuse this password with the password you use to access your router settings.
Modern routers Infolink often operate in two ranges: 2.4 GHz And 5 GHzIf your model is dual-band, you will need to set a password separately for each frequency or combine them under a single network name (Smart Connect function), if this option is supported by the firmware.
Selecting the encryption type and setting a password
The key point of the setup is choosing the encryption algorithm. In the list of available options, you will find WEP, WPA, WPA2 And WPA3The WEP protocol is considered obsolete and easily hacked, so its use is strictly not recommended even for older devices.
The optimal choice at the moment is WPA2-PSK (AES)This standard provides a high level of protection and is compatible with almost all modern gadgets. If your router supports WPA3, it makes sense to switch to it, but some older devices may stop seeing the network.
When creating your password, avoid obvious combinations like your date of birth or phone number. Use at least 12 characters, mixing uppercase and lowercase letters, numbers, and special characters. This will make brute-force attacks virtually impossible.
Security Protocol Comparison Chart
To better understand the differences between available security methods, let's look at their comparative characteristics. Choosing the right protocol directly impacts network speed and vulnerability to external attacks.
| Protocol | Security level | Compatibility | Recommendation |
|---|---|---|---|
| WEP | Low (easy to hack) | All devices | Do not use |
| WPA (TKIP) | Average | Old devices | Only if there are no other options |
| WPA2 (AES) | High | Almost all devices | Recommended standard |
| WPA3 | Maximum | New devices | For maximum protection |
As can be seen from the table, the balance between security and compatibility is best achieved in the standard WPA2Upgrading to newer standards may require updating network card drivers on older laptops or replacing hardware.
Save settings and reconnect
After entering a new password and selecting the encryption type, you must click the button Save or "Apply". In some router models Infolink changes take effect only after a device reboot, so the system may prompt you to restart immediately.
Once the router reboots, all devices will lose their WiFi connection. On your computer or smartphone, find your network in the list of available networks and select "Forget Network" or "Delete Profile" to prevent the device from trying to connect with the old, now incorrect password.
Enter the new access key and test your internet connection. If the connection is established successfully and the speed matches your plan's speed, the setup was successful. Your local network is now protected from unauthorized access by your neighbors.
Additional network security measures
Changing your WiFi password is just the first step. For increased security, it's also recommended to change the password for accessing the router interface (admin panel) to prevent unauthorized access to your settings.
Turn on the function MAC filteringIf you want to allow connections only to specific devices you know about, keep in mind that this creates an inconvenience for guests, who will have to manually whitelist their addresses each time.
It is also worth disabling the function WPS (Wi-Fi Protected Setup). Despite the convenience of connecting with a single click, this protocol has vulnerabilities that allow attackers to quickly gain access to the network. It's better to spend a minute manually entering the password than to take that risk.
⚠️ Warning: Disabling the WPS feature may be necessary to comply with modern cybersecurity standards, as methods for brute-forcing the WPS PIN have become publicly available.
What should you do if you forgot your new password?
If you've changed your password and forgotten it, but need to connect urgently, the only solution is to reset the router to factory settings using the Reset button. After that, you'll have to reconfigure your internet and WiFi settings using your provider's credentials.
Common problems and their solutions
Sometimes users encounter a situation where, after changing the password, devices cannot see the network or are unable to connect. This is often due to the DNS cache or the incorrect encryption type selected. Try rebooting the router and the client device.
If the router interface Infolink If the browser doesn't open, check your network card's IP address settings. It should obtain an address automatically (DHCP). In rare cases, clearing your browser's cache or logging in through incognito mode may help.
If you encounter "Unable to obtain an IP address" errors, make sure your router's DHCP server settings haven't exhausted the address pool. Typically, up to 254 addresses are available by default, which is more than enough for home use.
FAQ: Frequently Asked Questions
Where can I find my router's IP address if the sticker has worn off?
Right-click the network icon in the Windows system tray, select "Status," then "Details." The "Default Gateway" address is your router's IP address. On macOS, you can find this in "System Preferences" -> "Network."
Is it possible to change the password via phone?
Yes, if your smartphone is connected to the router's WiFi network or via a LAN adapter (OTG). The browser login and setup process is the same as for the desktop version.
Why doesn't the Infolink router save the new password?
This could be due to a full settings memory or a firmware error. Try a full reset and reconfigure the router. Also, make sure you click "Save" and not just "Apply."
Does a complex password affect internet speed?
No, the length and complexity of a WiFi password do not affect data transfer speed. Speed depends on the WiFi standard (n, ac, ax), airborne interference, and your provider's plan. The impact on the router's processor when using WPA2/AES encryption is negligible.
How often should I change my password?
For a home network, it's sufficient to change the password every 6-12 months or if you suspect unauthorized access. For office networks with a large number of employees, changing passwords more frequently is recommended.