How to change the password on an MTS router via phone: full instructions

Securing your home network starts with a strong access key, which is often forgotten for years. If you're wondering about How to change the password on an MTS router via phone, then data security is not an empty promise for you. Modern 4G routers allow you to manage them directly from a mobile device, whether Android or iOS, without having to connect a cable to a computer.

Changing your password only takes a few minutes, but requires careful attention to avoid accidentally locking your settings. It's important to understand that there's a difference between your login password and your web interface devices and a dongle for connecting to a Wi-Fi network. In this article, we'll examine both options, paying particular attention to the specifics of MTS equipment, which is often based on Huawei or ZTE platforms.

Before adjusting settings, make sure your smartphone is connected to the network you plan to edit. If you try to change settings remotely while out of range or while connected via mobile data, the security system will simply block you from accessing the control menu. Changing the password via the mobile interface requires an active connection to the MTS router's Wi-Fi hotspot.

Preparing for setup via a mobile browser

The first step is to physically connect and test the connection between your device and the router. Disable mobile data on your phone to ensure that traffic is actually going through the router's Wi-Fi. This will prevent errors when attempting to load the settings page, which is often located on a local address and not accessible from the outside network.

Open any browser on your smartphone: Chrome, Safari, Yandex Browser, or Opera. Enter the device's IP address in the address bar. This works for most MTS routers, including popular models. Huawei E5573 or ZTE MF791, the standard address is 192.168.8.1In some rare cases, especially on older models, the address may differ, for example, 192.168.0.1 or 192.168.1.1.

⚠️ Important: If the settings page doesn't open, check the sticker on the bottom of the router. It contains the exact IP address, as well as the factory username and password for logging into the management system.

After entering the address, you will see an authorization window. By default, the login and password are often the same and look like this: admin, or the password is listed on the same sticker under the name "Web password" or "Login password." Don't confuse it with your SIM card PIN.

• 📱 Make sure Wi-Fi is turned on on your phone and the name of your MTS network is visible.
• 🔌 Disable mobile internet (3G/4G/5G) in your phone settings during setup.
• 🌐 Enter in the address bar of your browser 192.168.8.1 and click "Go".
• 🔑 Enter your login and password to log in to the control panel (by default, it is often admin/admin).

Login to the MTS router control panel

The MTS router management interface may look different depending on the model and firmware version. Most often, you'll be taken to the main status monitoring page, which displays the signal strength, number of connected devices, and network name. To change the password, find the appropriate section in the menu.

In Huawei's classic interfaces, which are widely used by the operator, you need to go to the tab Settings (Settings), then select Wi-Fi and further Wi-Fi settings (Wi-Fi Settings). In newer firmware versions, the menu may be collapsed into a sidebar or hidden under the "Menu" button in the top corner of the screen.

If you see a password change prompt upon first login, the system will prompt you to create a new access key immediately. This is a standard security procedure that shouldn't be ignored. Make sure to write down the new information in a safe place, as saving it will make your old password invalid and disconnect all devices from the network.

It is worth noting that some modern MTS routers support control via a special mobile application. Huawei HiLink or MTS Wi-FiIn this case, logging in through a browser may redirect you to install the app. If you prefer to use the browser, look for the "Web interface" or "Advanced settings" link on the welcome screen.

Step-by-step instructions for changing your Wi-Fi network password

When you are in the wireless settings section, you will see a field labeled as SSID (network name) and WPA Pre-Shared Key or simply "Password." This second field is where you'll need to enter a new character combination. It's recommended to choose a password of at least 8 characters, using mixed-case letters and numbers.

After entering the new value, scroll down the page and be sure to click the button Save or ApplyWithout this action, all changes will remain only in the browser buffer and will not be applied to the router configuration. When saving, the connection will inevitably be lost.

Once the router applies the new settings, your phone will lose its Wi-Fi connection. You'll need to go to your smartphone's Wi-Fi settings, find your network (it may be marked as "Saved, Protected"), and select "Forget Network" or "Delete," then reconnect using the new password.

⚠️ Note: After changing your Wi-Fi password, all previously connected devices (TVs, laptops, tablets) will no longer see the network or will be unable to connect. You will need to enter the new key manually on each device.

Changing the password for entering the settings (Admin)

It's also worth considering the password that protects the router's control panel. Many users leave it at the factory default. admin, which is a security hole, since an attacker, having connected to your Wi-Fi, will be able to change any settings, including traffic redirection.

To change this password, go to the section System (System) -> Change password (Modify Password). Here you'll be asked to enter your current (old) password and the new one twice. Create a unique combination, different from your Wi-Fi password, to make it more difficult for potential hackers.

After changing the administrator password, your current browser session will be terminated. You will need to enter the address again. 192.168.8.1 and log in with the new credentials. Write down this password first, as it's impossible to recover without resetting the router.

Features of different MTS router models

The operator offers a wide range of equipment. Pocket routers of the series Huawei E5573 have a simplified interface, with key settings located on the main screen. Changing your password is a one-click process using the "Wi-Fi Settings" widget.

Stationary models such as MTS 4G Router (often rebadged ZTE or Huawei B-series devices) offer more advanced functionality. They may feature a guest network, MAC address filtering settings, and parental controls. The interface of these devices is more cumbersome, but the menu logic remains similar: look for the "Wireless" or "WLAN" section.

Supported devices HiLink May require initial setup via a smartphone app. In this case, the browser interface may be limited. If you can't find the option you need in the web version, try downloading the official app; it often duplicates all setup functions.

What if the interface is in English?

If your router displays the menu in English, look for the "Settings" -> "WLAN" -> "WLAN Basic Settings" section. The "WPA Pre-Shared Key" field is your password. Don't change the "SSID Name" unless you want to rename the network.

Solving common setup problems

Users often encounter a browser error message saying "Unable to access the site" when entering an IP address. This may mean that the phone is connected to the network but isn't receiving an IP address from the router. Try rebooting the router by power cycling it, or select "Static IP" in the Wi-Fi settings on your phone and manually enter an address in the 192.168.8.x range.

Another common issue is that the "Save" button is inactive or the page freezes. This often happens when using older browser versions or with ad blockers enabled. Try opening Incognito mode or using a different browser.

⚠️ Please note: Router interfaces and menus can be updated remotely by the operator. If the described paths don't match your screen, refer to the descriptive section names (Wi-Fi, Security, System) rather than the exact names in the instructions.

If nothing helps and the router is behaving erratically, a hard reset will help. There's a small hole on the router's case. ResetPress it with a paperclip for 10-15 seconds while the device is turned on. The router will reset to factory settings, and the password will be the one written on the sticker.

FAQ: Frequently Asked Questions

Can I change my password if I'm not connected to Wi-Fi?

No, to change router settings, your device must be within the local network. You must be connected to the MTS router's Wi-Fi, even if there's no internet access. Changing local gateway settings via mobile data (3G/4G) is not possible without special operator services.

What is the best password to use for Wi-Fi?

Use a combination of at least 10 characters, including uppercase and lowercase letters, numbers and special characters (e.g. Mts#Wifi2026!). Avoid simple sequences like "12345678" or date of birth.

What should I do if I forgot my router admin password?

For security reasons, it's impossible to recover a forgotten administrator password. The only solution is to perform a factory reset. After that, use the information from the sticker on the bottom of the device.

Does changing your password affect your internet speed?

Changing the password itself doesn't affect speed. However, if you change the encryption type from WPA2 to WPA3 on very old devices, speed may drop due to incompatibility. On modern MTS routers, it's better to select mixed mode or WPA2.