How to Share Wi-Fi from Your Phone to a DEXP TV: 3 Proven Methods + Troubleshooting

Connecting a TV DEXP Connecting to the internet via a smartphone is a convenient way to access online movie theaters, YouTube, or software updates when a router is not available. However, not all users know how to properly set up Wi-Fi sharing to avoid connection issues or low speeds. In this article, we'll discuss three working methods Internet distribution with Android And iPhone on TVs DEXP (including models DEXP H24F7000S, DEXP L32H7000T and others), as well as typical errors and their solutions.

Feature of TVs DEXP - using the operating system Android TV or a proprietary shell based on Linux, which affects the connection algorithm. For example, some models require manual entry of the IP address when distributing iPhone, while others may not see the network due to limitations in the access point settings. We tested all methods on current firmware versions from 2026–2026 and highlighted key nuances for stable operation.

1. Preparation: What to check before distributing Wi-Fi

Before setting up a hotspot on your phone, make sure your TV is DEXP and your smartphone meet the minimum requirements. This will eliminate most connection issues.

Phone requirements:

  • 📱 Android 8.0+ or iOS 12+ (on older versions there may be no distribution options Wi-Fi 5 GHz).
  • 🔋 Battery charge more than 50% — Internet distribution actively consumes energy.
  • 📶 Support Wi-Fi Direct or Hotspot (check in the "Wireless Networks" settings).
  • 🚫 No active VPN or proxy - they can block data transmission to TV.

TV requirements DEXP:

  • 📺 Model with module Wi-Fi (check the specifications or on the back panel - there should be a logo Wi-Fi Certified).
  • 🔄 Current firmware (outdated versions may not support WPA3 — an encryption standard used in new phones).
  • 🔌 No cable connected Ethernet — the wired connection has priority.

Make sure that mobile Internet (3G/4G/5G) is enabled on your phone.

Check that the TV is not actively connected to another Wi-Fi network.

Turn off Bluetooth on both devices (may cause interference)

Close background apps on your phone (saves data and battery) -->

If your TV DEXP released before 2019, may require manual IP configuration — we'll talk about this in the problem-solving section. Also, pay attention to The difference in distribution between Android and iPhone: Android TVs "see" access points from Android smartphones better due to protocol compatibility.

2. Method 1: Sharing Wi-Fi from an Android phone (tethering)

This is the most universal method, working on 90% of TVs. DEXPThe instructions are suitable for devices Samsung, Xiaomi, Huawei and other brands on Android.

Step 1: Enable tethering

  1. Open Settings → Wireless & networks → Tethering & portable hotspot (on some phones the item is called Access point and modem).
  2. Select Wi-Fi hotspot (or Portable Hotspot (on English firmware).
  3. Activate the slider and adjust the parameters:
    • 🔐 Network name (SSID): Come up with a simple name without spaces (e.g. DEXP-TV-Hotspot).
    • 🔒 Security type: select WPA2-PSK (the most compatible option).
    • 🔑 Password: minimum 8 characters, with numbers and letters (eg. Dexp1234!).

Step 2: Connect your TV DEXP to the access point

  1. On the TV remote, press Menu → Settings → Network → Wi-Fi.
  2. Select the created network (DEXP-TV-Hotspot) and enter the password.
  3. Wait for the status Connected (may take up to 30 seconds).

    4. Step 3: Check the connection

    Open the app on your TV YouTube or browser—if the pages load, the connection is successful. If the internet isn't working, check:

    • 📶 It's turned on on the phone mobile Internet (not just Wi-Fi).
    • 🔄 Network settings are selected on TV DHCP (automatic IP acquisition).
    • 🚫 There are no active traffic restrictions in the SIM card settings.

Android (Samsung, Xiaomi, etc.)

iPhone (iOS)

Huawei/Honor

Another brand-->

3. Method 2: Sharing Wi-Fi from iPhone (Personal Hotspot)

Televisions DEXP can connect to iPhone, but there are some nuances: some models do not support WPA3 — the encryption standard used by default in iOSIf the TV doesn't connect, you'll have to manually change the security settings.

Step 1: Turn on Personal Hotspot on iPhone

  1. Go to Settings → Tethering (or Personal Hotspot).
  2. Activate the slider and remember the password (it will be generated automatically).
  3. Leave it Maximum compatibility enabled (this will allow devices to connect without WPA3).

Step 2: Connect your TV DEXP

  1. On TV, select the network with your name iPhone (For example, iPhone (YourName)).
  2. Enter the password from the screen iPhone.
  3. If the connection does not occur, try turn off Maximum compatibility and reboot the TV.
What to do if your iPhone doesn't share the Internet?

1. Check that in Settings → Cellular → Data Options → Cellular Data Network included LTE/4G (Not 3G).

2. Make sure you have enough traffic (some operators block distribution when the balance is zero).

3. Reboot iPhone and TV at the same time.

4. If used eSIM, try switching to a physical SIM card - some operators limit the data transfer for virtual SIM cards.

Step 3: Solving the IP address problem (for older models) DEXP)

If your TV connects to the network but the internet isn't working, it's possible the IP address isn't being assigned. In this case:

  1. On TV, go to Settings → Network → IP Settings.
  2. Select Manually and enter:
    • IP address: 192.168.43.100
    • Gateway: 192.168.43.1
    • Subnet mask: 255.255.255.0
    • DNS: 8.8.8.8 (or 1.1.1.1)
  • Save the settings and restart the TV.

    • 4. Method 3: Connecting via Wi-Fi Direct (without sharing the Internet)

    If you need to transfer files (photos, videos) from your phone to your TV DEXP, but no internet access is required, you can use Wi-Fi DirectThis method is faster than Bluetooth and does not consume mobile data.

    Step 1: Activate Wi-Fi Direct on your TV

    1. Press on the remote control Menu → Settings → Network → Wi-Fi Direct.
    2. Select Turn on and wait until the TV becomes “visible” to other devices.

      3. Step 2: Connect your phone

      • 📱 On Android: Settings → Connections → Wi-Fi Direct → select your TV DEXP from the list.
      • 🍎 On iPhone: use the app File Explorer or Send Anywhere (Wi-Fi Direct is not supported natively).

      Step 3. Transfer files

      After connection:

      • On Android open Gallery, select files and click Send → Wi-Fi Direct.
      • On the TV, confirm the reception of files (they will be saved to the internal memory or to a flash drive, if one is connected).

      5. Compatibility table: which models DEXP support distribution from a phone

      Not all TVs DEXP Work equally well with Wi-Fi distribution. Below is a compatibility table for popular models (data based on user tests and official specifications).

      TV model 5 GHz support Compatibility with Android Hotspot iPhone Hotspot Compatibility Notes
      DEXP H24F7000S ❌ No ✅ Yes (2.4 GHz) ⚠️ Requires manual IP May lose connection under high load
      DEXP L32H7000T ✅ Yes ✅ Yes ✅ Yes Works better with Android 10+
      DEXP U24H7000 ❌ No ✅ Yes ❌ No (problems with WPA3) It is recommended to use Android-telephone
      DEXP I24G7000 ✅ Yes ✅ Yes ✅ Yes (with maximum compatibility) Supports Wi-Fi 6 on firmware versions 2023+
      DEXP S32G7000 ✅ Yes ✅ Yes ⚠️ Possible lag when streaming Better to use 5 GHz for 4K content

      If your model is not in the table, check the specifications on the official website. DEXP or in the user manual. Please note: some TVs with Wi-Fi 5 GHz may not see networks from older smartphones (released before 2018).

      6. Common mistakes and their solutions

      Even with proper setup, problems can still arise. Let's look at the most common errors and how to fix them.

      Error 1: The TV does not find the network from the phone

      • 🔍 Check network visibility: On your phone, disable the "Hide network" mode in the access point settings.
      • 📶 Change range: if the TV does not support 5 GHz, force install 2.4 GHz in the modem settings.
      • 🔄 Reboot both devices: Sometimes a simple reboot of the phone and TV helps.

      Error 2: There is a connection, but the Internet is not working

      • 🌐 Check your APN settings: on your phone go to Settings → Mobile network → Access point names (APN) and make sure that the parameters meet the requirements of your operator.
      • 🔒 Disable your firewall: some antiviruses (for example, Kaspersky or Avast) block internet distribution.
      • 📱 Reset network settings: Perform a reset on your phone Settings → System → Reset → Reset network settings.

      Error 3: Slow speed or connection drops

      • 📊 Limit background apps: Close all traffic-consuming programs on your phone (for example, TikTok or Telegram).
      • 🔋 Connect your phone to the charger: When the battery level is low, the smartphone may limit the upload speed.
      • 📡 Use a signal repeater: If the phone is far from the TV, the signal weakens - place the devices closer to each other.
      What should I do if my TV says "Unable to obtain IP address"?

      This error occurs when the DHCP server on the phone doesn't assign an address to the TV. Solutions:

      1. Manually enter the IP address on the TV (as in method 2 for iPhone).

      2. On your phone, turn the hotspot off and on again.

      3. Check if the "Traffic Saver" mode is enabled on your phone (it may block DHCP).

      ⚠️ Attention: If you use dual-SIM Phone internet tethering can only work with one SIM card (usually slot 1). Check your modem settings and swap the cards if necessary.

      7. Distribution Optimization: How to Improve Speed ​​and Stability

      To ensure Wi-Fi sharing from your phone works as efficiently as possible, follow these tips:

      1. Select the optimal Wi-Fi channel

      By default, the phone selects a channel automatically, but it may be congested with other networks. To change it manually:

      • Install the application on your phone WiFi Analyzer (For Android) or Network Analyzer (For iOS).
      • Check which channels 2.4 GHz or 5 GHz are the least loaded.
      • In your phone's hotspot settings, select a free channel (for example, Channel 6 For 2.4 GHz).

      2. Limit the number of connected devices

      Each additional device (tablet, laptop) reduces speed. If the TV lags while sharing:

      • Disconnect unnecessary gadgets from the access point.
      • Set a connection limit on your phone (usually up to 5 devices).

      3. Use an external antenna (for older phones)

      If your smartphone has a weak Wi-Fi module (for example, Samsung Galaxy J-series or Xiaomi Redmi 4A), you can connect external antenna via adapter OTGThis will improve coverage by 20-30%.

      8. Alternative ways to connect a TV DEXP to the Internet

      If sharing from your phone is inconvenient or unstable, consider other options:

      1. Connection via cable Ethernet

      If there is a router near the TV, use a wired connection:

      • Buy an adapter USB-to-Ethernet (if there is no port on the TV LAN).
      • Connect the cable from the router to the TV.
      • In the TV network settings, select Wired connection.

      2. USB modem (3G/4G)

      Some models DEXP (For example, DEXP L32H7000T) support USB modem connection:

      • Buy a 4G modem (for example, Huawei E3372).
      • Insert it in USB port TV.
      • In the network settings, select Mobile Internet.

      3. Powerline adapters

      If the router is far from the TV, use adapters Powerline, transmitting the Internet through electrical wiring:

      • Connect one adapter to the router and the second one next to the TV.
      • Connect the second adapter to the TV via Ethernet or Wi-Fi (if the adapter model supports distribution).
    ⚠️ Attention: When using a USB modem on a TV DEXP Please check the manual for the list of supported devices. Some modems require additional drivers that cannot be installed on Android TV.

    FAQ: Frequently asked questions about distributing Wi-Fi on DEXP

    Is it possible to share Wi-Fi from a phone to a TV? DEXP without password?

    Technically yes, but it's not safe. If you leave the hotspot open (Without security), outsiders will be able to connect to your network, which will reduce speed and create a risk of data leakage. On TVs DEXP With firmware older than 2020, open networks may not connect due to security policy. Android TV.

    Why TV? DEXP Connects to the access point, but pages don't load?

    The reasons may be as follows:

    1. Mobile Internet is disabled on your phone (check the icon 4G/5G in the status bar).
    2. The operator blocks the distribution (for example, Tele2 or Iota may limit traffic for access points).
    3. The TV is not tuned correctly DNS - try to write it manually 8.8.8.8.

    Also check if the phone is in the "Don't worry" mode. Saving traffic - it can block data transmission.

    How to share Wi-Fi from your phone to your TV DEXP, if there is no mobile Internet?

    If you only have home Wi-Fi (from a router), but you want to share it with your TV via your phone, do the following:

    1. Connect your phone to your home Wi-Fi.
    2. Turn on the hotspot on your phone (as in Method 1).
    3. On TV, connect to your phone's network.

    ⚠️ Important: Not all phones support this "bridge". Samsung And Xiaomi it works, and on some models Huawei - No.

    How much traffic is used when distributing Wi-Fi to a TV?

    Consumption depends on the content:

    • SD quality (480p): ~0.7 GB/hour.
    • HD quality (720p–1080p): ~1.5–3 GB/hour.
    • 4K (Ultra HD): ~7–10 GB/hour.
    • Online games: ~0.1–0.3 GB/hour (without downloading updates).

    If you have a limited data plan, please disable autoplay videos in YouTube and adjust the streaming quality in applications (for example, in Kinopoisk HD or Netflix).

    Is it possible to share Wi-Fi from a phone to a TV? DEXP and use the internet on your phone at the same time?

    Yes, but it depends on the phone:

    • On Android 10+ and iOS 13+ You can simultaneously use mobile Internet on your phone and distribute it on TV.
    • On older versions Android (8–9) When the access point is turned on, the mobile Internet on the phone is disabled.

    To check: enable seeding, then try opening the website on your phone. If the pages load, then simultaneous use is supported.

    📖 Read also

    Portable Wi-Fi router: which one to choose and how to set it up? Choosing the best router to take with you. A review of Pocket WiFi, MiFi, and USB modems. How to share your internet while traveling. How to Find Out if Wi-Fi Is Free: 7 Ways to Check Detailed instructions: how to distinguish a free Wi-Fi network from a paid one. Check via a browser, app How to connect to Wi-Fi on Lastochka: full instructions A detailed guide to setting up Wi-Fi on Lastochka trains. Learn how to find the Russian Railways network and log in. How to Make a Wi-Fi Router from a Laptop: A Complete Guide Learn how to share Wi-Fi from your laptop to your phone using the command line and Windows settings. How to Share Wi-Fi with a USB Modem: Complete Setup Guide Detailed instructions on how to share Wi-Fi from a modem flash drive via a router or laptop. Setting up a USB modem What is Wi-Fi on a SIM card called: official terms 2026 Let's understand the terminology: eSIM, Wi-Fi Calling, mobile hotspot and other names for wireless