Modern laser printers such as HP Laser 135w, are designed for maximum mobility and convenience, allowing you to print documents without unnecessary wires. However, initial wireless connection setup often becomes a stumbling block for users accustomed to a traditional USB connection. This process requires careful attention, as the device must correctly "see" your home network and receive an IP address from the router.
In this article, we'll walk you through all the steps involved in establishing a Wi-Fi connection between your computer and printer. You'll learn about automatic and manual setup methods, as well as how to avoid common errors that occur during driver installation. Proper setup wireless network will ensure stable printing from any device in the home.
Equipment preparation and compatibility testing
Before you begin software setup, you must ensure that all system components are ready for operation. Printer HP Laser 135w Supports 802.11 b/g/n standards, meaning it's compatible with most modern routers, but there are some frequency considerations. Make sure your router is broadcasting at 2.4 GHz, as many budget printer models can't see 5 GHz networks without a special bridge.
Place the device in an area with a strong signal. Walls, microwaves, and other electronic devices can create interference that will cause the connection to be lost during driver installation. If the printer is located far from the router, it's best to move it closer during setup and then return it to its original location after a successful connection.
- 📶 Check that the router is turned on and distributing the Internet.
- 🔌 Make sure the printer is connected to a power source and turned on using the power button.
- 💻 Prepare the computer or smartphone from which you will perform the setup.
- 📄 Find out the password for your Wi-Fi network, you will need it to enter it.
⚠️ Important: If AP Isolation is enabled on your router, devices on the network will not be able to see each other. To use the printer, you must temporarily disable this feature in your router settings.
It's also worth checking whether guest network mode is enabled on the router for the primary device being configured. This can sometimes prevent the printer from being detected on the local network.
Resetting the printer's network settings
If the printer was previously used on a different network or setup was unsuccessful, old configurations may have been stored in the device's memory. This is a common reason why wireless connection indicator The indicator light is blinking, but the connection is not established. Before trying again, we recommend resetting the network settings to factory defaults.
To do this, go to the control panel HP Laser 135w Find the button with the wireless network icon or the cancel button (red cross). Pressing and holding this button for a few seconds (usually about 5-7) will reset the settings. The lights on the panel should blink, indicating the reset.
After the reset, the printer will enter connection standby mode, and the Wi-Fi indicator will begin blinking blue. This means the device is ready to search for a network or configure via WPS.
- 🔄 Resetting eliminates IP address conflicts.
- 🗑️ Saved passwords for old networks are deleted.
- 📡 The printer enters the search mode for a new connection.
It is important to understand that after the reset, all computers on the network will lose connection with the printer, and the driver installation procedure will have to be repeated on each device.
WPS method: quick connection without password
The easiest way to connect HP Laser 135w To connect to Wi-Fi, use WPS (Wi-Fi Protected Setup). This method automatically transfers the network password, eliminating the need to manually enter it on the printer's control panel, which often lacks a full-fledged display.
Press the WPS button on your router. It can be physical or software (in the router interface). After activating the router's search mode, you have about two minutes to initiate the process on the printer. Press and hold the wireless button on the control panel. HP Laser 135w until the indicator starts flashing.
☑️ Checking the WPS connection
The devices will automatically exchange encryption keys. If everything is successful, the Wi-Fi indicator on the printer will turn solid blue. This means security protocol agreed upon and the connection established.
⚠️ Note: Some ISPs or corporate networks block the WPS function for security reasons. If the button on the router doesn't respond or the connection fails, use the USB cable setup method.
It's worth noting that the WPS method only works if the router is within line of sight or in close proximity to the printer at the time of pairing.
Setup via USB cable and software
If automatic methods fail, the most reliable option is to use a temporary USB connection. To do this, you'll need to download the full package of drivers and utilities from the official website. HPFind the model Laser 135w in the support section and download the installer for your operating system.
Run the downloaded file and follow the on-screen instructions. When prompted to select a connection type, select "Wireless Connection." The installer will prompt you to temporarily connect the printer to your computer via a USB cable. At this point, the program will retrieve the Wi-Fi settings from your computer and transfer them to the printer.
Driver installation: Run setup.exe -> Select connection type -> USB connection -> Transfer Wi-Fi settingsOnce the printer confirms receiving the network settings, the installer will ask you to disconnect the USB cable. After this, the device will attempt to connect to the router automatically. If the indicator light turns solid, you can complete the driver installation.
| Stage | User action | Printer response |
|---|---|---|
| 1 | Launching the installer | The indicators are on |
| 2 | USB connection | The USB indicator lights up |
| 3 | Data transfer | The Wi-Fi indicator is flashing |
| 4 | Disconnecting the cable | The Wi-Fi light is on steadily. |
This method is especially useful if your network name contains special characters or Cyrillic that the printer may not recognize correctly when entered manually.
Using the HP Smart app for mobile devices
For smartphone and tablet users, the company HP developed an application HP Smart, which greatly simplifies the setup process. The app is available for iOS and Android and allows you to manage your printer remotely. Download the app from the official store and create an HP account.
Turn on Bluetooth on your smartphone and launch the app. Tap “Add Printer” or the plus sign. The app will find HP Laser 135w and will offer to share passwords for the Wi-Fi network your phone is connected to. This eliminates the need to manually enter long passwords.
What should I do if the app doesn't see the printer?
Make sure Bluetooth and location are enabled on your phone. Also, check that your phone is connected to the 2.4 GHz network, not the 5 GHz network if your router splits the two.
After successful setup, you can use the app to not only print documents and photos, but also monitor toner levels, scan documents directly to PDF, and send them to cloud services.
- 📱 Convenient control interface from your phone.
- ☁️ Possibility of printing from the cloud.
- 🖨️ Scan directly into the app.
It's important to note that some app features may require your printer to be registered with HP+, which requires a constant internet connection.
Diagnostics and troubleshooting (common problems)
Even if you follow the instructions carefully, there may be situations where the printer HP Laser 135w The Wi-Fi indicator won't connect. Often, the problem lies in incompatible encryption standards or router settings. If the indicator light continues to flash, try temporarily disabling MAC filtering on your router.
Another common cause is a static IP address. Make sure it's enabled in your router settings. DHCP server, which automatically assigns addresses to devices. If you manually assigned IP addresses, make sure they are in the same subnet.
⚠️ Note: Antivirus software or Windows Firewall may be blocking the printer from being detected on the network. Try temporarily disabling them during installation.
Also, check that your router hasn't reached its maximum number of connected devices. In home networks with a large number of devices, the router may simply not assign a new address to the printer.
If all else fails, print a network configuration report (usually using a key combination on the panel) to see the error code, which will give you a specific indication of the cause of the failure.
Why can't my printer see my Wi-Fi network?
Most likely, your router is broadcasting a network at a frequency of 5 GHz, and HP Laser 135w It only works in the 2.4 GHz band. You need to go into your router settings and enable 2.4 GHz broadcasting or combine the network names (SSIDs) into one.
How to find out the IP address of a printer?
Press and hold the wireless button on the printer for 5 seconds. The device will print a configuration report, which will list the current IP address in the Wireless section.
Is it possible to connect a printer to a hidden network?
Yes, but only through the HP Smart software or the driver installer from a computer, where you need to manually enter the network name (SSID) and password, since the automatic search does not see hidden networks.
What to do if the orange Wi-Fi light is on?
Orange usually indicates a connection error or low signal strength. Check your password, distance to the router, and make sure the network doesn't require additional authorization via a web page.