Modern office tasks require mobility, and the ability to print documents directly from a laptop or smartphone without unnecessary wires is becoming critical. Model HP Laser MFP 135w While the 10.1000 is one of the most popular solutions in the compact laser MFP segment, initial wireless connection setup often presents challenges for users. The process isn't simply a matter of entering a password; it requires an understanding of the network protocol and the correct sequence of actions.
Unlike inkjet analogs, laser devices of the series Laser 108/135 have a specific control interface, tied to a combination of buttons and indicators, which can be confusing for a beginner. Connection stability This depends directly on how accurately you complete the preparatory steps before running the setup wizard. Errors at the initial stage often result in the computer simply not seeing the printer on the local network.
In this article, we will examine in detail all the connection steps, from resetting old settings to installing drivers in operating systems. Windows And macOSYou'll learn how to avoid common IP address conflicts and why dual-band routers can cause problems for older network modules. It is critical to understand that this model only supports the 2.4 GHz standard, so trying to connect to a 5 GHz network will always fail.
Preparing equipment and checking network compatibility
Before moving on to the software, you need to make sure the hardware is physically ready and that your home network settings meet the device's requirements. Printer HP Laser MFP 135w The device is equipped with a Wi-Fi module that operates exclusively in the 2.4 GHz frequency range. If your router broadcasts a single network with the same name (SSID) for both bands or uses the WPA3 standard, you may have difficulty detecting the device.
Make sure you know the exact name of your wireless network and its password. Complex passwordsStrings containing special characters may sometimes be incorrectly read by the printer's control panel, so it's best to use combinations of letters and numbers during setup. Also, make sure the distance between the router and the MFP doesn't exceed reasonable limits, as laser printers are often installed in niches or cabinets where the signal can be weakened.
Pay attention to the indicators on the front panel of the device. Is the wireless indicator lit? Is it blinking? The status of these lights provides basic information about the current state of the module. If the device was previously used on a different network, it is recommended to reset the network settings to avoid configuration conflicts.
- 📶 Make sure your router is transmitting a signal in the 2.4 GHz range (802.11b/g/n standard).
- 🔑 Prepare your Wi-Fi password, preferably without exotic characters, to avoid typing errors.
- 🔌 Position the printer HP Laser 135w at a distance of no more than 5-7 meters from the signal source for confident tuning.
- 📱 Charge your mobile device or prepare the laptop from which you will perform the initial configuration.
⚠️ Attention: If your router uses the "Smart Connect" feature (combining 2.4 and 5 GHz into a single network), the printer may not connect. Temporarily separate the networks in your router settings or create a guest network for the 2.4 GHz band only.
Checking compatibility is the foundation of a successful setup. Ignoring signal frequency requirements means that searching for networks on your computer or phone screen simply doesn't produce any results. Some corporate networks may require MAC address devices to add to the whitelist, which can be found by printing the configuration report.
Reset network settings and activate setup mode
If the printer HP Laser MFP 135w If you previously connected to a different access point or changed your provider, the old configuration may be blocking the new connection. The device's network module automatically attempts to connect to a known network, and if it's unavailable, it may not enter discovery mode. To resolve this issue, you need to force the Wi-Fi setup mode.
The reset and activation procedure is performed directly from the MFP control panel. You'll need to locate the button with an image of an antenna or wireless network. Pressing this button switches the device to different modes depending on how long you hold it. To enter Setup Mode, you typically hold the button until the wireless indicator starts flashing blue.
Sequence of actions:1. Press and hold the Wireless (antenna) button.
2. Watch the indicator: it should start flashing.
3. Release the button when the flashing becomes constant (setting mode).
Once the indicator light starts flashing, the device has created its own access point or entered connection standby mode (Wi-Fi Direct). At this point, the printer is ready for pairing. If the indicator light is solid blue, the device is already connected to a network and must first be disconnected or reset via the menu.
⚠️ Attention: Do not turn off the printer while the Wi-Fi indicator is blinking. Interrupting the network module initialization process may cause a software failure requiring a firmware update.
It is important to distinguish between the regime Wi-Fi Direct and infrastructure network connection mode. In our case, we're setting up a connection to the router so all devices in the house can see the printer. Wi-Fi Direct mode is used for direct printing from a phone without a router, which is a separate use case.
Installing HP Smart Drivers and Software
Modern devices HP require installation of a full driver package for all functions to function correctly, including network scanning. Operating systems Windows 10 And Windows 11 Devices often attempt to automatically detect the device, but basic drivers don't provide full functionality. Therefore, the first step should be downloading the latest software from the official website.
Go to the support page HP and enter the model of your device - Laser MFP 135wThe system will offer to download the full driver package or utility. HP SmartFor desktop PCs, a full driver package is preferable, as it includes the necessary network utilities and diagnostic tools. For mobile devices and tablets, an app is sufficient. HP Smart.
☑️ Pre-installation check
During installation, the program will ask you for your connection type. Select "Wireless" or "Wi-Fi." The utility will begin searching for the device on the network. If you followed the steps in the previous section correctly (activated setup mode), the installer will detect the printer. At this point, you may need to temporarily connect a USB cable to transfer network settings if automatic detection fails.
Follow the on-screen instructions of the setup wizard. The program will automatically transfer the network name and password to the printer. After a successful data transfer, the Wi-Fi indicator on the MFP should stop blinking and turn solid blue. This indicates that the device has received the connection. IP address from the router and ready to work.
Setting up via WPS: A quick connection method
If your router supports the technology WPS (Wi-Fi Protected Setup) connection process HP Laser MFP 135w can be significantly simplified by avoiding manual password entry. This method is ideal for users who don't want to navigate complex menus or are afraid of making a mistake when entering characters.
To implement this method, your router must have a physical WPS button or a corresponding function in the web interface. WPS mode must also be activated on the printer's control panel. This is usually done by long-pressing the wireless network button (more than 3-5 seconds) until the indicator light starts blinking in a pattern different from the normal setup mode.
After activating the mode on the printer, press the WPS button on the router. The devices will begin exchanging encryption keys. This process takes about 2 minutes. If the connection is successful, the printer's indicator will glow solid, and a notification about a new device on the network will appear on your computer.
- 🔘 Find the WPS button on your router (often marked with two arrows).
- ⏱️ Press the WPS button on the router and immediately activate WPS mode on the printer HP 135w.
- 📡 Wait until the Wi-Fi indicator on the printer stops blinking and remains on continuously.
- ✅ Check the list of available printers on your computer.
What to do if WPS doesn't work?
The WPS function may be disabled in your router's security settings or may not be supported by your ISP. Some router models also have a time limit for activating the mode (only 30 seconds). In this case, use the driver installation method.
Troubleshooting Discovery and IP Addressing Issues
Even with the correct settings, situations may arise when the computer does not see the printer. HP Laser MFP 135wMost often, the problem lies in the devices being on different subnets or a firewall blocking the connection. It's also possible that the printer has received a new IP address, different from the one specified in the driver.
To diagnose the printer, you need to find out its current IP address. This can be done by printing a network configuration report. On the device's control panel, press the "Cancel/Stop" button or a combination of buttons (depending on the firmware version) to initiate printing. In the report, look for the line IPv4 Address.
Compare the first three digits of your computer's and printer's IP addresses. They must match. For example, if your computer's address is 192.168.1.5, your printer's should be 192.168.1.X. If the addresses are different (for example, 192.168.0.X and 192.168.1.X), the devices won't see each other.
If the IP addresses are in different subnets, try rebooting the router and printer. In complex cases, you may need to manually assign a static IP address through the printer's web interface (EWS). To do this, enter the device's IP address in the browser's address bar.
| Problem | Possible cause | Solution |
|---|---|---|
| The indicator is flashing | There is no connection to the router | Check the password and network name (SSID) |
| Offline printer | The IP address has changed | Remove the device and add it again |
| Scanning error | Blocked by firewall | Allow the HP app to access the network |
| No response from EWS | Port conflict | Use HTTP instead of HTTPS or reset your settings |
⚠️ Attention: Antivirus programs and the built-in Windows firewall often block network scanning. When running a scan for the first time, be sure to allow access for all applications. HP in the security pop-up window.
Setting up network printing and scanning
After a successful connection, it's important to ensure that not only basic printing functions but also advanced features, such as network scanning, are working. For full scanner functionality, the scanner component must be installed on the computer. HP Scan or similar, included in the full driver package.
To print a test page, go to "Devices and Printers" (or "Printers & Scanners" in Windows 10/11). Right-click on HP Laser MFP 135w, select "Printer Properties" and click "Test Print." If the page prints, then printing protocol works correctly.
To set up scanning, open the application HP Smart or HP ScanSelect your printer from the list. If the device shows as "Available," try scanning. In some cases, you may need to configure a scan profile, specifying the file format (PDF/JPG) and destination folder.
Regularly check toner levels and component status via the web interface or app. Timely cartridge replacement and cleaning of the scanner optics will extend the life of the device. HP Laser MFP 135wAlso, don't forget to update the firmware through the service menu, as new software versions often contain fixes for network bugs.
Frequently Asked Questions (FAQ)
Can the HP Laser 135w be connected to a 5GHz network?
No, model HP Laser MFP 135w The device is equipped with a Wi-Fi module that only supports the 802.11b/g/n standard in the 2.4 GHz frequency range. Connecting to 5 GHz networks (802.11ac/ax) is technically impossible. If your router is broadcasting a single network with a shared name, try separating them in the router settings or using a 2.4 GHz guest network.
What should I do if the computer doesn't see the printer after installing the drivers?
First, check if the Wi-Fi indicator on the printer is solid. If it's blinking, there's no connection. Make sure your computer and printer are connected to the same network (check the IP addresses). Try temporarily disabling your antivirus and firewall. If the problem persists, remove the device from the printer list and run the driver installation again, selecting "Connect a new printer."
How do I find the IP address of my HP 135w printer?
The most reliable way is to print a network configuration report. To do this, press and hold the "Cancel" button (or the button combination specified in the instructions, often the wireless button and the copy button) on the control panel until printing begins. In the report, look for the "Network Status" or "IPv4 Address" section.
Does the HP Laser 135w support cloud printing (HP ePrint)?
Model 135w Belongs to the budget series and has limited network services functionality. Full support for HP ePrint and cloud features may not be available or may require connection via a mobile app. HP SmartBasic functions are limited to printing over a local network and Wi-Fi Direct.
Is it possible to connect a printer via USB and then switch it to Wi-Fi?
Yes, this is the standard installation scenario. You connect the device via USB cable, launch the full driver package installation, and during the installation process, the wizard will prompt you to change the connection type to wireless. The program will automatically transfer the Wi-Fi settings from your computer to the printer, after which you can disconnect the cable.