Modern Smart TVs transform a regular screen into a multimedia center, but without internet access, they lose much of their functionality. For owners of Salut devices, which often run on the Android TV platform, a stable wireless connection is key to streaming, gaming, and installing apps. The setup process is usually straightforward, but there are some nuances worth knowing beforehand.
In this article we will take a detailed look at How to connect a Salute speaker or TV to your home network. We'll cover standard scenarios, methods for manually entering parameters, and solutions to common connection issues. Proper configuration of the router and signal receiver will help avoid interruptions and delays when viewing high-definition content.
Before you begin, make sure your router is turned on and broadcasting a signal, and your TV is in a strong reception area. If you just purchased your device or reset it to factory settings, the initial setup procedure may differ slightly from adding a new network. In any case, the basic principles remain the same for all models.
Preparing equipment and checking the network
Before you begin setting up, make sure that your Wi-Fi router It's working correctly. Check if other devices, such as smartphones or laptops, can connect to it. This will help rule out a problem with your ISP or the router itself. If the internet is working on other devices, you can proceed to preparing the TV.
It's important to know what frequency your home network operates on. Modern routers often support two bands: 2.4 GHz and 5 GHz. The former provides greater coverage but lower speeds, while the latter offers higher speeds but a shorter range. For viewing 4K content, the latter is preferable. 5 GHz band.
It's also worth checking if MAC address filtering is enabled on your router. If this feature is enabled, you'll need to find the TV's unique ID and add it to the router's whitelist. This is usually done through the router's web interface, but this protection is rarely used in home networks.
⚠️ Note: If you're using a guest Wi-Fi network with a login portal (which requires entering a phone number or password on a web page), the TV may not connect using the standard method. In such cases, it's best to use a separate router or access point mode on your smartphone.
Standard connection procedure via menu
The primary way to activate the wireless module is in the system settings. The interface may vary slightly depending on the firmware version, but the logic remains the same. You need to find the section responsible for network connections.
Use your remote control to navigate. Go to the main menu and find the gear icon or the "Settings" section. Then select "Network & Internet" or a similar option. Here you'll see a list of available wireless networks.
- 📺 Press the "Menu" or "Settings" button on the remote control to open the main menu.
- 🌐 Select the "Network" or "Network & Internet" section in the sidebar.
- 📡 Wait for the scan to complete and select your network name (SSID) from the list.
- 🔑 Enter your password using the on-screen keyboard and confirm the action.
After entering the password, the TV will attempt to obtain an IP address automatically. If the credentials are correct, you'll see a message indicating a successful connection. This window typically also displays the signal strength and current connection speed. If the status is "Connected" but the internet isn't working, check the date and time on your device.
☑️ Check before connection
Manual configuration of IP and DNS parameters
In some cases, automatic retrieval of settings via protocol DHCP may fail. This often happens in complex networks with multiple routers or when address conflicts occur. Manually assigning a static IP address is then required.
To do this, select "Advanced" or "Advanced Settings" in the network selection menu. Switch the IP type from "Automatic" to "Static." You'll need to enter the information corresponding to your subnet. Typically, this is the gateway (router) address and subnet mask.
| Parameter | Example of meaning | Description |
|---|---|---|
| IP address | 192.168.1.150 | Unique address of the TV on the network |
| Gateway (Router) | 192.168.1.1 | Your router's address |
| Subnet mask | 255.255.255.0 | Determines the size of the local network |
| DNS 1 | 8.8.8.8 | Google's name server |
DNS servers deserve special attention. Providers sometimes provide their own DNS servers, which can be slow or block access to certain services. Replacing them with public ones, such as Google (8.8.8.8) or Cloudflare (1.1.1.1), often solves the problem of slow app loading times.
Where can I find my router's IP address?
Your router's IP address (default gateway) is usually written on a sticker on the bottom of the device. It's most often 192.168.0.1 or 192.168.1.1. You can also find it in the network settings on your connected smartphone under "Network Information."
Using WPS for a quick connection
Technology Wi-Fi Protected Setup Allows you to connect devices without entering a password. This is convenient if you have a complex encryption key that's difficult to enter with the remote control. However, this feature must be supported by both devices: the router and the Salut TV.
The process is as follows: select the WPS connection method in the TV menu. After that, you'll have about two minutes to activate pairing mode on the router. On most models, this requires pressing a physical button on the router.
If your router doesn't have a dedicated WPS button, you may need to press and hold the connect button for a few seconds. The TV will automatically detect the signal and establish a connection. This method is less secure, as anyone with physical access to the router can connect to your network.
⚠️ Warning: The WPS feature is considered vulnerable to cybersecurity threats. If you don't use it regularly, we recommend disabling WPS support in your router's settings via the web interface to prevent unauthorized access.
Setting up via a mobile app
Many modern Salut TVs support control and initial setup via smartphone. This is achieved by transmitting Wi-Fi settings from the phone to the TV. This is especially useful if the on-screen keyboard is not working properly.
Download the official TV control app (such as Android TV Remote Control or the brand's proprietary app) to your smartphone. Make sure your phone is connected to the same Wi-Fi network you want to connect the TV to, or use your mobile data for the initial Bluetooth pairing.
- 📲 Launch the app on your smartphone and click "Search for devices".
- 📺 Select your Salute TV from the list of found devices.
- 🔗 Follow the on-screen instructions to confirm the pairing code.
- 📶 In the app, go to network settings and select the desired Wi-Fi network.
After successfully transferring the settings, the TV will reboot the network module and connect to the internet. This method is also convenient because it allows you to use your smartphone's keyboard to enter passwords, which is much faster and more convenient.
Troubleshooting connection issues and errors
Even with the correct settings, errors can still occur. One of the most common issues is when the TV detects the network but fails to connect, displaying an authentication error. This most often indicates an incorrect password or incompatible encryption type.
Make sure the security type on your router is set to WPA2-PSK or WPA3Older encryption standards, such as WEP, may not be supported by newer Salut models. Also, check your router settings to see if there's a limit on the number of connected devices.
If the problem persists, try a full network reset. In the TV menu, find "Reset network settings" or "Forget network." Then, delete the network profile on the router and reconnect. In rare cases, updating the firmware via a USB drive may help.
Why doesn't the TV see the 5 GHz network?
Not all Salut TV models are equipped with dual-band Wi-Fi modules. If your TV only supports 2.4 GHz, it will not be able to detect a 5 GHz network. Check the technical specifications for your model in the manual or on the official website. In this case, connect to a 2.4 GHz network.
How to increase Wi-Fi speed on TV?
For maximum speed, use the 5 GHz band and ensure the TV is within direct line of sight of the router. Walls and household appliances (microwaves, baby monitors) can cause interference. If the signal is weak, consider purchasing a Wi-Fi repeater or connecting via LAN cable.
What should I do if the internet connection disappears after an update?
Firmware updates sometimes reset network settings or change drivers. Try forgetting the network and reconnecting. If that doesn't help, perform a factory reset, but keep in mind that this will delete all installed apps.
Is it possible to share Wi-Fi from a phone to a TV?
Yes, you can use your smartphone as a hotspot. However, keep in mind that video content uses a lot of data. Make sure you have an unlimited data plan, otherwise you may get an unpleasant surprise on your mobile phone bill.