How to Connect a Samsung M2070 Printer to a Laptop via Wi-Fi Without a Disk: A Complete Guide

Introduction: Why connect a printer via Wi-Fi and is it possible to do without a disk?

Wireless printer connection Samsung M2070 Connecting a printer to a laptop saves time and eliminates cable clutter. This is especially important for offices or home workstations where multiple devices need to print on a single MFP. But what if the driver disc is lost or the laptop simply doesn't have a disc drive? It turns out you can connect a printer via Wi-Fi without it—just download the necessary software from the official website and configure the network correctly.

Model Samsung M2070 supports wireless connection via Wi-Fi Direct and standard protocol WPS, but many users encounter difficulties during initial setup. In this article, we'll cover all connection methods—from automatic installation via Windows Update to manually setting up the printer's IP address. And if something goes wrong, you'll also find solutions to the most common errors here.

Before you begin, make sure your laptop and printer are on the same Wi-Fi network. If your router supports dual band (2.4 GHz / 5 GHz), temporarily disable 5 GHz - Samsung M2070 works only on frequency 2.4 GHzThis is one of the common reasons why devices "don't see" each other.

How to connect a Samsung M2070 to a laptop without a drive

There are three main methods for setting up a wireless connection. The choice depends on the capabilities of your router and laptop operating system:

• 🔄 Automatic connection via WPS — the fastest way if the router supports the technology Wi-Fi Protected Setup (button WPS on the body).
• 🖥️ Manual setup via the printer panel — a universal method that works even on old routers without WPS.
• 🌐 Connecting via Wi-Fi Direct — allows you to print without a router, directly from your laptop (but requires re-configuration each time you turn it on).

If your router was released after 2015, it most likely supports WPS. This method takes less than a minute: just press a button. WPS on the router and confirm the connection on the printer. However, this method has a limitation— Some Samsung M2070 models are not compatible with routers from Rostelecom and MTS providers due to firmware issues.In this case, manual configuration will help.

⚠️ Note: If the printer was previously connected to a different network, reset its settings. To do this, hold down the button Stop (⏹) 5 seconds until all lights flash. This will clear the old Wi-Fi settings.

Step-by-step instructions: connecting via WPS

This method works for most modern routers. Follow these instructions:

1. Make sure your router is turned on and is distributing Wi-Fi at the correct frequency. 2.4 GHz.
2. Find the button on the router body WPS (usually labeled or marked with a 🔄 icon). Press and hold it for 2-3 seconds.
3. On the printer Samsung M2070 go to the menu: press Menu → Network → WLAN → WPS → Push Button.
4. Wait for the message Connected on the printer display (usually takes 30-60 seconds).

If the Wi-Fi light on your printer is blinking green but there is no connection, check:

• 📶 The distance between the printer and the router (should be no more than 5 meters).
• 🔒 The MAC address filter is disabled on the router (if enabled, add the printer's MAC address to the list of allowed addresses).
• ⚡ Power on the router - some models reset WPS after rebooting.

After successful connection, print network report (click Menu → Reports → Network Config) to find the printer's assigned IP address. You'll need it to install drivers on your laptop.

Manual Wi-Fi setup on the Samsung M2070 printer

If WPS doesn't work or your router doesn't support it, set up the connection manually through the printer's control panel:

1. On the printer, press Menu → Network → WLAN → Setup Wizard.
2. Select your Wi-Fi network from the list. If it's not there, enter the name (SSID) manually.
3. Please specify the security type (WPA2-PSK for most home networks) and a password.
4. Confirm the settings and wait for the message Connected.

If your printer doesn't find your network, check:

• 📡 SSID visibility - some routers hide the network name (enable this option in the router settings) Broadcast SSID).
• 🔐 Password Correctness - Printers Samsung are case-sensitive and sensitive to special characters (e.g. ! or #).
• 📶 Wi-Fi channel - if the router is operating on a channel 12–14, try changing it to 1–11 (in the router settings).

⚠️ Caution: When setting up manually, the printer may get stuck while obtaining an IP address. If the Wi-Fi indicator blinks orange for more than 2 minutes, restart the printer and router. If the issue persists, assign a static IP address in the router settings (bind it to the printer's MAC address).

How to find the MAC address of the Samsung M2070 printer?

Print a network report (Menu → Reports → Network Config) or look for a sticker on the back of the printer - the MAC address is located next to the serial number.

Installing drivers on a laptop without a disk

After connecting the printer to Wi-Fi, you need to install the drivers on your laptop. There are three ways to do this:

We recommend downloading the driver from official Samsung website (section "Support → Drivers and Software"). Enter the printer model (SL-M2070) and select your operating system. Download the file Samsung Universal Print Driver - it fits most models of the series M20xx.

If after installing the driver the printer is not displayed in the list of devices:

1. Open Control Panel → Devices and Printers.
2. Click Add a printer.
3. Select Add a network, wireless, or Bluetooth printer.
4. If the printer is not found automatically, click The printer you need is not in the list and enter its IP address (you can find it in the network report).

Troubleshooting connection errors

Even with proper setup, problems can still arise. Here are the most common errors and their solutions:

• 🔴 Error: "Unable to connect to printer"
  

  Make sure the printer and laptop are on the same network. Temporarily disable Windows Firewall (Control Panel → Firewall → Turn off).

• 🟡 The Wi-Fi indicator is blinking orange
  

  This means the printer isn't receiving an IP address. Restart your router or assign a static IP address in its settings.

• 🟢 The printer is connected but does not print.
  

  Remove the printer from the device list and add it again, manually entering the IP address. Also, check if there's a print job waiting in the queue (Control Panel → Devices and Printers → View print queue).

If the printer connects but disconnects after a few minutes, the problem may be with your router's power saving settings. Go to your router's control panel (usually at 192.168.1.1 or 192.168.0.1) and disable the option Wi-Fi Power Save or Green Mode.

⚠️ Attention: On some router firmware versions TP-Link And ASUS printers Samsung M2070 may be disabled due to the function Band Steering (automatic switching between 2.4 GHz and 5 GHz). Disable it in your router settings if you experience connection drops.

Connecting via Wi-Fi Direct (without a router)

If you don't have a router or need to temporarily connect the printer directly to your laptop, use Wi-Fi DirectThis mode creates an access point on the printer itself, which can be connected to like a regular Wi-Fi network.

Algorithm of actions:

1. On the printer, press Menu → Network → Wi-Fi Direct → On.
2. Remember or write down the network name (SSID) and password that appear on the display.
3. On your laptop, connect to this network via Control Panel → Networks and Internet → Manage networks.
4. Set up your printer as a network device (the printer's IP address in Wi-Fi Direct mode is usually 192.168.3.1).

Please note: In Wi-Fi Direct mode, your laptop will lose internet access. To print and surf the web at the same time, connect your laptop to the internet via Ethernet cable or USB modem.

Also note that turning off the printer disables the Wi-Fi Direct access point. You'll need to reconnect the next time you turn it on. This method is convenient for one-time tasks, but isn't suitable for regular use.

FAQ: Answers to frequently asked questions

Can I connect the Samsung M2070 to a macOS laptop?

Yes, but you'll need to download the driver from the official Samsung website (Mac OS section). After installation, add the printer via System Preferences → Printers & Scanners, by selecting the option Add a printer or scanner. It should appear in the list. Samsung M2070 with a note Bonjour.

The printer is connected, but it prints blank pages. What should I do?

Most likely, the problem is with the driver. Uninstall the current driver via Control Panel → Programs and Features, then download the latest version from the Samsung website. Also, check the toner level: click Menu → Reports → Supplies Info and print the report.

How do I reset my printer's Wi-Fi settings if I've forgotten the network password?

Hold the button Stop (⏹) 5 seconds, until all lights flash. This will reset the printer's network settings to factory defaults. After the reboot, you can set up the Wi-Fi again.

Can this printer be connected to a phone?

Yes, through the app Samsung Mobile Print (Available for Android and iOS). Connect your phone to the same Wi-Fi network as the printer, then add the device in the app. To print via Wi-Fi Direct on your phone, select the printer's network in the Wi-Fi settings.

Why does my printer print very slowly over Wi-Fi?

The reasons may be different:

• Weak Wi-Fi signal - move the printer closer to the router.
• Congested network - Disconnect other devices from Wi-Fi while printing.
• Low toner quality - replace cartridge (the printer slows down when the toner level is low).
• Outdated driver - update the software on the official website.