How to connect a Samsung printer to a computer via Wi-Fi: 2026 instructions

Wireless printer connection Samsung Connecting to a computer via Wi-Fi saves desk space, eliminates cable clutter, and allows you to print from multiple devices simultaneously. However, many users encounter issues: the printer can't find the network, drivers won't install, or the connection keeps dropping. In this article, we'll look at all connection methods — from standard settings via the control panel to manual addition of the printer by IP address.

We will pay special attention to Samsung models with Wi-Fi Direct support (e.g. SL-M2020 or Xpress M2070), which can create their own network for direct connection. We'll also look at common mistakes, such as 0x0000000d or Failed to connect to printer, and ways to eliminate them without calling a specialist.

The instructions are valid for operating systems Windows 10 and 11, as well as for most printers Samsung 2018–2026 releases. If your model is older, check the technical specifications for Wi-Fi support—some budget devices (e.g., ML-1660) work only via USB.

1. Preparing the printer for wireless connection

Before setting up the connection, make sure the printer is plugged into a 220V network and is within range of your Wi-Fi router (ideally no further than 5 meters). If the device is new, perform the initial setup:

• 📦 Unpack the printer and remove all protective films, especially from the paper feed rollers.
• 🔌 Connect the power cable and press the power button. Wait for the self-test to complete (the indicators will stop flashing).
• 📄 Load paper into the tray (recommended size is A4, density 80 g/m²).
• 🖨️ Print a test page (usually the button Test Print or retention Cancel within 3 seconds).

If the printer has been used before, reset network settings to factory settings. To do this:

1. Click Menu (or Settings) on the control panel.
2. Go to Network → Reset Network (the path may differ depending on the model).
3. Confirm the reset with the button OK.

⚠️ Attention: After the reset, the printer will lose all saved Wi-Fi networks. If you previously connected to it via USB, you should disconnect the cable—it may be blocking the wireless setup.

2. Methods for connecting a Samsung printer via Wi-Fi

Exists three main methods Wireless connection. The choice depends on the printer model and your router's capabilities:

Let's look at each method in detail. Start with the simplest one - WPS.

Make sure your router supports WPS (there's a button on the router's body)

The printer is turned on and located near the router (within a radius of 2 meters)

The router is in WPS mode (the indicator is blinking or green)

Disable all VPNs and proxies on your computer-->

3. Connect via WPS (the fastest way)

Technology WPS (Wi-Fi Protected Setup) Allows you to connect your printer to the network without entering a password. This method works if:

• 📡 Your router supports WPS (usually there is a physical button with this label).
• 🔒 The protocol is enabled on the router WPA2-PSK (Not WPA3 - some older printers do not support it).
• ⏱️ The printer and router are close together (maximum 2–3 meters).

Step-by-step instructions:

1. Click the button WPS on the router and hold for 2-3 seconds until the indicator starts flashing.
2. On the printer, go to the menu Network → Wi-Fi → WPS (path may differ).
3. Select Push Button Method and confirm to start the network search.
4. Wait for the message Connected on the printer display (usually takes 30-60 seconds).

If the printer does not connect:

• 🔄 Restart your router and printer.
• 📶 Check that the router is in the enabled mode 2.4 GHz (Samsung printers often don't work with 5 GHz).
• 🔑 Make sure that the function is not enabled on your router MAC filtering.

⚠️ Attention: Some providers (eg Rostelecom or Beeline) disable WPS by default on their routers. To enable it, go to the router's web interface (usually at 192.168.0.1 or 192.168.1.1) and activate WPS in the section Wi-Fi → Security.

4. Manual connection: entering SSID and password

If WPS doesn't work or your router doesn't support it, you'll have to enter your network details manually. This method is universal and works for all models. Samsung with Wi-Fi.

Step 1: Find your network's SSID and password:

• 📋 Look at the sticker on the back of the router (usually the factory numbers are indicated there) SSID And Password).
• 💻 Or open the list of networks on your computer: click the Wi-Fi icon in the system tray → Network properties.

Step 2: Enter the data on the printer:

1. On the printer, go to Menu → Network → Wi-Fi → Manual Setup.
2. Select your network from the list (or enter SSID manually if the network is not in the list).
3. In the field Password Enter your Wi-Fi password. Use the arrow keys to select characters.
4. Confirm the connection with the button OK.

If the printer gives an error Authentication Failed:

• 🔠 Check the case of the characters in the password (Samsung printers are case-sensitive).
• 🔄 Restart your router and printer.
• 📡 Try temporarily disabling network encryption (install Open in the router settings), connect the printer, and then return WPA2-PSK.

5. Connecting via Wi-Fi Direct (without a router)

Function Wi-Fi Direct Allows you to connect a printer directly to your computer, bypassing the router. This is convenient for temporary printing or if you don't have a home network. However, this method has its limitations:

• 🖥️ Only one device can be connected at a time.
• 📶 Data transfer speed is lower than via a router.
• 🔌 The printer will not be accessible to other devices (phones, tablets).

How to enable Wi-Fi Direct:

1. On the printer, go to Menu → Network → Wi-Fi Direct.
2. Turn on the feature (On).
3. Remember or write down SSID And password, which the printer will generate automatically (for example, DIRECT-HP-Samsung M2020).
4. On your computer, connect to this network as you would to a regular Wi-Fi network.

Once connected, the printer will only be accessible to devices connected to its direct network. To return to normal mode, disconnect Wi-Fi Direct in the printer menu.

⚠️ Attention: Some printer models (eg. Samsung SL-M2875) When Wi-Fi Direct is activated, they are automatically disconnected from the main network. To print from multiple devices, use a standard connection through a router.

6. Installing drivers and adding a printer in Windows

Even after successfully connecting to Wi-Fi, the printer won't work until you install the drivers and add it to the system. Here's how:

Step 1. Download drivers:

• 🌐 Go to the official website Samsung to the support section (support.samsung.com).
• 🔍 Enter your printer model (e.g. Xpress M2070) and select it from the list.
• 📥 In the section Downloads download driver for your OS (Windows 10/11 x64 or x86).

Step 2. Install the printer on the system:

1. Open Start → Settings → Bluetooth & devices → Printers & scanners.
2. Click Add a device → Add manually.
3. Select Add a printer by TCP/IP address.
4. In the field Name or IP address Enter the printer address (can be found in the printer menu: Network → Wi-Fi → IP Address).
5. Specify the port Standard TCP/IP Port and press Next.
6. Select the downloaded driver or let Windows find it automatically.

If Windows does not find the driver:

• 📁 Specify the path to the downloaded file manually (usually this is a folder Downloads).
• 🔄 Restart your computer and try adding the printer again.
• 🛠️ If the driver does not install, try Samsung universal driver (search by request Samsung Universal Print Driver).

What should I do if the printer is connected but does not print?

If your printer appears in the list of devices but does not respond to print tasks:

1. Check the print queue: open Control Panel → Devices and Printers, right-click on the printer and select View the print queueDelete all frozen documents.

2. Restart the printing service: Click Win + R, enter services.msc, find Print Manager and restart it.

3. Check your firewall: temporarily disable it or add an exception for the printer in the settings Windows Defender.

7. Solving common errors

When connecting the printer Samsung Users often encounter common problems with Wi-Fi. Here's how to fix them:

If the printer prints blank sheets or the text comes with stripes:

• 🖨️ Check the toner level (for laser printers) or ink (for inkjet printers).
• 🔧 Clean the print head through the printer menu (Settings → Maintenance → Clean Print Head).
• 📄 Make sure the paper is facing the correct way (usually logo side up) in the tray.

8. Optimizing Wi-Fi printing

To ensure stable wireless printing, follow these tips:

• 📶 Place the printer and router no more than 5 meters apart. Avoid obstacles (walls, metal objects).
• 🔄 Configure it on your router static IP address for the printer so that it doesn't change when you reboot. To do this:

1. Go to the router's web interface (192.168.0.1 or 192.168.1.1).
2. Find the section DHCP → Static Lease (or Address reservation).
3. Add the printer by its MAC address (indicated on the sticker or in the menu) Network).
4. Assign an IP address outside the DHCP range (e.g. 192.168.0.100).

To speed up printing of large documents:

• 🖼️ In the printer settings (Control Panel → Devices and Printers → Printer Properties) select the mode Draft or Quick Print.
• 📎 Disable duplex printing if you don't need it.
• 🖥️ Close other programs using the network (torrents, online games).

⚠️ Attention: If you use the printer in an office with a large number of devices, it is recommended to allocate a separate network for it. VLAN or customize QoS on the router to avoid delays when printing.

Frequently Asked Questions (FAQ)

My Samsung printer can't connect to my Wi-Fi network. What should I do?

First check:

• Is Wi-Fi enabled on the printer (the indicator should be on or flashing).
• Does the printer support the frequency? 2.4 GHz (many models do not work with 5 GHz).
• Is your network's SSID hidden in your router settings?

If the network still doesn't show up, try connecting manually by entering SSID on the printer. Also, update the printer firmware via Samsung Printer Software.

How to find the IP address of a Samsung printer?

There are three ways:

1. Print network report: on the printer, go to Menu → Network → Print Network Config.
2. Look at the display: Menu → Network → Wi-Fi → IP Address.
3. Via the router: go to the web interface and check the list of connected devices (DHCP Clients List).

Is it possible to connect a Samsung printer to Wi-Fi without a display?

Yes, but the process is more complicated. You'll need:

1. Connect the printer to the computer via USB.
2. Install the program Samsung Easy Printer Manager.
3. Select in the program Setting up a wireless network and follow the instructions.

For models without a display (eg. Samsung ML-2165W) This method is the only option for setting up Wi-Fi.

The printer is connected, but printing is very slow. How can I speed it up?

The problem usually lies in the network or printer settings:

• Switch the router to the mode 802.11n (and not 802.11b/g).
• Disable the option in the printer settings. High data compression ratio.
• Install the printer as network, and not as a local one (through TCP/IP port).
• Check if the Wi-Fi channel is busy with other devices (for example, streaming video).

How to reset network settings on a Samsung printer?

To reset your printer to factory network settings:

1. Turn off the printer.
2. Press and hold the button Cancel (or Stop) and hold it for 10-15 seconds, while turning on the printer.
3. Release the button when the message appears on the display. Network Reset.

After the reset, all saved Wi-Fi networks will be deleted and the printer will create a new network. Wi-Fi Direct with factory password.