Modern office and home tasks require high mobility, and wired connections often become an unnecessary limitation. Wireless printing allows you to place the device in any convenient location, maintaining access to it from several computers simultaneously. Model HP Laser MFP 135w is a popular budget solution that supports operation via the 802.11 b/g/n network standard.
The setup process may seem complicated at first glance if you don't know the correct sequence of steps. Errors most often occur when selecting the connection type in the driver installer or when entering the router password. In this article, we'll walk you through a detailed procedure that will help you avoid common pitfalls and maintain stable operation. integrate a printer to your local network.
Before you begin, make sure your MFP is turned on and the cartridge is installed. It's also crucial that your computer and printer are within range of a strong router signal. We'll cover the USB cable setup method, as it's the most reliable way to initially configure the device's wireless module.
Preparing equipment and checking network parameters
The first step is to check the physical condition of the equipment and the readiness of the infrastructure. Make sure that The HP Laser MFP 135w is plugged in and the power light is solid. If the device has been previously used with another computer, it may need to be reset network settings to factory values.
The second important aspect is the stability of your wireless router. Printers in this class often only operate in the 2.4 GHz band and may not see 5 GHz networks unless they are combined into a single SSID on the router. Make sure you know your Wi-Fi password, as you'll need to enter it during the setup process.
⚠️ Important: Make sure the VPN client is disabled on your computer before beginning the installation. Virtual network tunnels can prevent the driver installer from detecting the printer on the local network.
For successful installation, you'll also need a USB Type AB cable (the printer's standard square connector). Even if you plan to use the device only over the air, the cable is necessary for the initial Wi-Fi configuration transfer.
- 📄 Check if there is a free USB port on your computer.
- 📶 Make sure your laptop is connected to the same Wi-Fi network you want to connect the printer to.
- 🔌 Prepare an original or high-quality USB cable no longer than 2 meters.
Downloading software from the official website
Using the supplied disc is a recipe for trouble, as the driver versions on them are often outdated. HP Laser MFP 135w needs to download the latest package Full Feature Software From the manufacturer's official support portal. This ensures compatibility with the latest Windows or macOS operating system updates.
Go to the HP support website and enter your device model in the search bar. The system will prompt you to select your operating system; it's usually detected automatically, but it's best to double-check the version (e.g., Windows 10 or 11). You'll need a file with the word "Full" or "Complete" in the name, as basic drivers may not include Wi-Fi configuration utilities.
After downloading the file, run it. This will not install the printer immediately; it will only unzip the temporary installer files to a hidden folder. Wait for the unzipping process to complete before proceeding to the next step.
Step-by-step instructions for setting up a Wi-Fi connection
The most reliable method is to use a USB cable to transfer the initial network settings. Run the unpacked installer and follow the on-screen instructions. When prompted to select a connection type, select Wireless connection (Wireless).
When selecting a setup method, select "Yes, I want to use a USB cable to set up my wireless network" (or similarly, "First-time USB setup"). The program will prompt you to connect the cable. At this point HP Laser MFP 135w must be turned on.
☑️ Connection checklist
The installer will automatically scan for available networks and transmit the SSID and password to the printer. The wireless indicator on the device's panel should start blinking and then turn solid, indicating a successful connection. The program will then prompt you to disconnect the USB cable.
| Indicator | State | Meaning |
|---|---|---|
| Wireless communication | Flashing blue | Setup mode or network search |
| Wireless communication | It's blue | Successful connection to Wi-Fi |
| Attention | Flashing orange | Connection error or no cartridge |
| Attention | It's glowing orange | Critical error or jam |
Installing drivers and completing configuration
Once the cable is disconnected, the installer will continue working over the network. They will find the device using the IP address assigned to the printer by the router and install the necessary settings. print drivers and scanning. This process may take several minutes.
During installation, you may be prompted to register your device or set up automatic updates. These steps are optional. If you do not want to receive promotional emails, uncheck the corresponding boxes. The main thing is to wait for the message confirming the installation is successful.
⚠️ Important: If your antivirus or firewall software requests network access for HP components, be sure to select "Allow." Blocking network access will prevent documents from printing.
After the process is complete, it's recommended to print a test page to ensure the data is transferred correctly. To do this, select "Print a test page" in the printer properties in the control panel.
Setting up network printing and scanning
After installation The HP Laser MFP 135w becomes available to all devices on the same network. You can print documents without a physical connection. For scanning, use the app. HP Scan or the standard Windows Fax and Scan tool.
It's important to note that network scanning features may require additional activation in the device menu or HP Printer Assistant. Make sure the correct profile and file save format are selected in the scan settings.
If you're using a router with a guest network feature, remember that devices on the guest network are often isolated from the main network. The printer and computer must be on the same network segment (the same VLAN or subnet), otherwise they won't be able to see each other.
- 🖨️ To print, select HP Laser MFP 135w from the list of available printers.
- 📄 To scan, launch the software and click the "Scan" button.
- ⚙️ To check the status, open HP Printer Assistant.
Diagnosing and troubleshooting connection errors
The most common issue is that the printer isn't visible on the network after setup. In this case, check the device's IP address by printing a network configuration report (usually using a key combination on the panel or through the menu). Compare the first three digits of the printer's IP address and the computer's IP address—they should match.
If the connection is interrupted, the router may have changed the printer's IP address after a reboot. The solution is to configure a static IP address through the router's web interface or the printer itself (via EWS). Also, try rebooting both the router and the printer simultaneously.
What to do if the orange indicator is on?
An orange wireless indicator often indicates that the Wi-Fi password is incorrect or the signal is too weak. Try moving the printer closer to the router and repeating the USB setup process.
In some cases, antivirus software may block ports that are necessary for operation. network protocols Printing. Temporarily disable the firewall to test. If the issue resolves, add an exception for HP executable files.
Frequently Asked Questions (FAQ)
Is it possible to connect the HP Laser MFP 135w to Wi-Fi without a USB cable?
Yes, this is possible through the printer's menu if it has a display, or via WPS if your router supports it. However, the USB cable method is considered the most reliable for initial setup.
Does this model support Wi-Fi Direct?
The 135w model typically supports direct connection, but activating it may require installing the full driver package and configuring it through the device menu. This allows you to print without a router, directly from your phone or laptop.
Why can't the computer see the scanner over the network?
Often, the scanner driver is installed separately or requires the WIA/TWAIN service to be running. Check in Windows "Services" to see if the "Print Spooler" service and HP services are running.
What is the default password for an HP printer?
The printer itself doesn't have a Wi-Fi password; you enter your network's password. Login to the web interface (EWS) is usually not required, and the password is often blank or found on a sticker on the back of the device.