Wirelessly connecting a modern MFP to a home or office network allows you to print documents from any device, be it a laptop, smartphone, or tablet. HP Laser MFP 130 This compact laser model allows for quick setup without the hassle of cables. However, initial setup requires strict adherence to the correct procedure. Errors during driver installation or Wi-Fi password entry often result in the device becoming inaccessible to the computer, creating the false impression that it's malfunctioning.
The process of integrating a printer into a local network is based on the use of a utility HP Smart or the classic driver installer from the manufacturer's website. It's important to understand that MFP 130 It doesn't have a full-fledged touchscreen for password entry, so all network settings are managed through software on a PC or mobile device. Properly preparing the equipment before setup significantly reduces the time needed to resolve potential address conflicts.
Preparing equipment and checking the network
Before you begin installing the software, you must make sure that HP Laser MFP 130 is operational and ready for pairing. Make sure the cartridge is installed and the device lid is tightly closed, as sensors may block network modules from starting when the lid is open. Wireless module The printer is automatically activated when turned on, but initial setup often requires a temporary USB connection or using the WPS feature if your router supports it.
Checking your Wi-Fi network frequency is crucial. Most 130 series models operate exclusively in the 2.4 GHz, while modern routers often distribute the network at a frequency 5 GHzIf your computer is connected to a high-speed 5 GHz network and your printer is searching for a 2.4 GHz network, they won't "see" each other, even if they're in the same room.
⚠️ Attention: Make sure Client Isolation isn't enabled on your router, which prevents devices on your local network from communicating. This is a common cause of a printer being connected to Wi-Fi but the computer being unable to print.
Also, make sure that VPN services and proxy servers are disabled on your computer, as they can redirect traffic and block detection of local devices. For proper operation printing protocol Both devices must be in the same subnet segment.
☑️ Pre-installation check
Setup via the HP Smart app
The most modern and convenient way to set up HP Laser MFP 130 is the use of a proprietary application HP SmartIt automatically detects the printer model and suggests the optimal connection scenario. The app is available for Windows, macOS, Android, and iOS, making the process universal across all platforms.
To get started, download and install the app from the official website or the Microsoft Store. Once launched, click the "Add Printer" button or the plus icon. The app will begin searching for available devices within range. If the printer is new and hasn't yet been configured, it may be in setup mode, indicated by a blinking wireless indicator on the control panel.
- 📶 Click "Set up a new device" in the list of found printers.
- 🔑 Enter your Wi-Fi network password in the window that appears (the app often fills it in automatically).
- ⏳ Wait until the process is complete; the indicator on the printer should stop flashing and remain solid blue.
During the setup process, the application may request a firmware update (firmware). It is strongly recommended that you agree to this action, as new software versions often contain Wi-Fi module bug fixes and improve connection stability.
What should I do if HP Smart doesn't see my printer?
If the automatic search doesn't yield results, try temporarily connecting the printer to your computer via a USB cable. The HP Smart app can use the USB connection to transfer network settings, after which you can disconnect the cable.
Using the WPS method for quick connection
If you don't want to enter your password manually or have difficulty using the keyboard, you can use technology WPS (Wi-Fi Protected Setup)This method allows you to connect HP Laser MFP 130 to the router by simply pressing buttons, but it requires physical proximity of the devices and support of the function by your router.
Press and hold the wireless button on the printer's control panel for 3-5 seconds until the light starts flashing. Then, within 2 minutes, press the WPS button on your router. The devices will automatically exchange encryption keys.
| Wi-Fi indicator | State | Meaning |
|---|---|---|
| Flashing blue | Setup mode | The printer is ready to connect. |
| It's blue | Connected | The network is active and you can print. |
| It's glowing orange | Error | Incorrect password or weak signal |
| Turned off | Disabled | The wireless module is turned off |
This method is especially convenient if you have a complex Wi-Fi password containing special characters that are difficult to enter through the settings interface. However, it's important to remember that WPS is considered a less secure protocol, and some network administrators prefer to disable it for security reasons.
Installing drivers and software
After successful connection HP Laser MFP 130 When connected to a network, Windows or macOS may automatically install basic drivers. However, for full scanner operation and print settings, you must install the full software package. Basic drivers often limit the device's functionality.
Go to the official HP support page and enter your device model. The system will prompt you to download the package. HP Laser MFP 130 Full Feature Software and DriverLaunching the installer will begin the process of searching for the printer on the network. If the previous steps were completed correctly, the installer will detect the device by IP address.
During installation, you may be asked to select a connection type. Select "Wireless" or "Network." If the installer prompts you to connect a USB cable to transfer settings, follow the on-screen instructions. After installation is complete, it is recommended to restart your computer to ensure all system printing services correctly register the new device.
- 🖨️ Make sure that it appears in the list of devices HP Laser MFP 130 Series PCLm-S.
- 📄 Check the scanner's operation using the Windows Scan or HP Smart app.
- ⚙️ Go to the printer properties and adjust the energy saving settings.
Setting up a static IP address
For stable operation in an office or home, where the network configuration often changes, it is recommended to assign HP Laser MFP 130 static IP address. By default, printers obtain an address dynamically via DHCP, and when you reboot the router, the address may change, which will lead to loss of connection with the computer.
To assign the address, open the printer's web interface (EWS). To do this, enter the device's current IP address into the browser's address bar (you can find it by printing a configuration report or viewing it in the HP Smart app). Go to the "Networking" tab -> "IPv4 Protocol."
⚠️ Attention: When assigning a static IP address, ensure it is outside the range of addresses assigned by the router's DHCP server to avoid IP address conflicts. For example, if your router assigns addresses from 100 to 200, assign the printer address 50.
Change the address acquisition method from "Automatic (DHCP)" to "Manual." Enter the desired IP address, subnet mask, and gateway (usually your router's address). After applying the settings, the printer may reboot the network module, and you will need to enter the new address in your browser to access the interface.
Solving common problems
Despite the simplicity of the procedure, users may encounter difficulties when connecting HP Laser MFP 130Often, the problem lies in Windows Firewall or antivirus settings that block incoming connections from the printer. In such cases, you need to add an exception for the HP app or allow it to work on a private network.
If your printer shows up as "Offline," check your signal strength. Laser MFPs often have metal housings, which can shield the signal if the device is in a recess or behind a thick wall. Try moving your router closer or using a Wi-Fi repeater.
- ❌ "Printer not found" error: Check if the SSID (network name) is hidden.
- 🔄 Reset settings: Press and hold the Wireless button and the Cancel button simultaneously for 3 seconds to reset the network settings.
- 🔌 Reboot: Turn off the router and printer, turn on the router, wait until it fully boots up, then turn on the printer.
In some cases, uninstalling the old driver via Control Panel -> Devices and Printers and reinstalling it, clearing the print cache, can help. To do this, find the Print Spooler service in services.msc and restart it.
Why is my printer printing slowly over Wi-Fi?
Delays may be caused by Wi-Fi congestion from neighboring networks. Try changing the wireless network channel to 1, 6, or 11 in your router settings to avoid interference.
Frequently Asked Questions (FAQ)
Can the HP Laser MFP 130 be connected to a 5GHz network?
No, this model only supports the standard 802.11 b/g/n, which operates in the 2.4 GHz band. If your router broadcasts a single network with a common name (Smart Connect), try separating them in the router settings or connecting to a 2.4 GHz guest network.
How to find a printer's IP address without a computer?
Press and hold the Wireless button on the control panel for 5 seconds. The printer will print a network configuration report, which will list the current IP address in the IPv4 section.
Does the HP Laser MFP 130 support printing from a phone?
Yes, once connected to Wi-Fi, you can print from Android and iOS smartphones using the app. HP Smart or built-in printing services (Mopria, AirPrint), if supported by your OS version.
What to do if the orange Wi-Fi light is on?
Orange usually indicates a connection error or a weak signal. Check that the password you entered is correct. If the password is correct, move the printer closer to the router and ensure there are no strong sources of interference between them, such as microwave ovens.