How to connect the HP Smart Tank 519 printer to Wi-Fi: complete instructions with photos and tips

Connecting a printer HP Smart Tank 519 Connecting to a wireless network is a challenge that every device owner faces. Despite its apparent simplicity, the process can be challenging, ranging from network invisibility to authentication errors. In this article, we'll explore all connection methods — via the printer control panel, mobile application HP Smart and even manually via WPS if the automatic method does not work.

Feature of the model Smart Tank 519 — the lack of a display, which makes menu navigation difficult. However, the manufacturer compensates for this with intuitive indicator lights and voice assistant support. We'll show you how to correctly interpret the printer's signals, which buttons perform what functions, and what to do if Wi-Fi network is not found or the device refuses to connect. You'll also learn how to check the connection and set up printing from your phone or computer.

Important: If your router uses 5 GHz or non-standard security settings (for example, WPA3-Enterprise), the printer may not connect. We'll explain how to bypass these restrictions without compromising network security. And at the end of the article, you'll find answers to frequently asked questions, including resetting the printer and updating the firmware.

1. Preparing for connection: what you need to check before starting

Before you begin setup, make sure all the necessary conditions for a successful connection are met. This will save time and avoid common errors.

Network requirements:

• 📶 The router must broadcast the network in the range 2.4 GHz (the printer does not support 5 GHz). If your router only works on 5 GHz, enable compatibility mode or create a separate network for devices 2.4 GHz.
• 🔒 Network security type — WPA2-PSK (AES). WPA3 or mixed mode (WPA/WPA2) may cause problems. If necessary, change the settings in the router's admin panel.
• 📡 The printer's Wi-Fi signal must be stable. If the printer is located far from the router, use a repeater or move the device closer.

Printer requirements:

• 🔋 Make sure the printer is turned on and connected to a power source. The power light should be on. green light without flashing - this means that the device is ready for setup.
• 🖨️ There must be paper (at least one sheet) in the tray. The printer may request a test print to confirm the connection.
• 📱 Prepare your smartphone or computer for setup. The app must be installed on it. HP Smart (for mobile devices) or HP drivers (for PCs).

Make sure your router is broadcasting 2.4 GHz|

Check network security type (WPA2-PSK)|

Turn on the printer and wait for the green indicator|

Place paper in tray|

Download the HP Smart app to your phone/PC-->

If you're using a corporate network or guest Wi-Fi (for example, in an office or hotel), the connection may be blocked. In such cases, you'll need to contact your network administrator to add the printer's MAC address to the list of allowed devices.

⚠️ Attention: Some providers (eg Rostelecom or Beeline) disable network SSID broadcasting by default. If your Wi-Fi is hidden, temporarily enable network visibility in your router settings; otherwise, the printer won't be able to detect it.

2. Method 1: Connecting via the printer control panel (without an app)

This method is suitable if you don't have a smartphone or prefer to configure devices manually. The instructions are for a printer. HP Smart Tank 519 with firmware version 22.3.5 and newer.

Step 1: Activate Wi-Fi Setup Mode

1. Press and hold the button Wi-Fi (with the antenna icon) on the printer panel for 5 secondsuntil the indicator starts flashing blue and green.
2. Release the button. The printer will enter network search mode.

Step 2: Select a network and enter a password

3. Indicator Wi-Fi will blink blue — this means the printer is searching for available networks. Wait until it starts blinking. green (at least one network found).
4. Click the button Wi-Fi once. The indicator will flash. orange — the printer is waiting for a password to be entered.
5. Find the button on your router WPS (usually on the back panel) and press it for 2 minutesIf there is no button, proceed to method 3 (manual password entry).

Step 3. Confirming the connection

• If the connection is successful, the indicator Wi-Fi will light up green without blinking.
• The printer will print automatically connection report with network information (name, MAC address, IP). Save this sheet—it will be useful for setting up printing from other devices.

If WPS doesn't work or your router doesn't support it, use alternative method with manual password entry through the application HP Smart (described in the next section).

3. Method 2: Connecting via the HP Smart app (recommended)

Mobile application HP Smart Simplifies setup and provides additional features, such as scanning documents to the cloud or printing from social networks. Download it:

• 📱 Android
• 🍎 iOS

Step 1: Launch the Setup Wizard

1. Open the app HP Smart and press Add a printer (the “+” icon in the upper right corner).
2. Select Setting up a new printer → Wireless network.
3. The app will prompt you to enable Bluetooth to search for the printer. Allow access.

Step 2: Connecting the printer to your phone

4. On the printer, press and hold the button Wi-Fi And Information (with the "i" icon) simultaneously during 3 secondsThe indicator will start flashing. blue.
5. In the application, select yours HP Smart Tank 519 from the list of found devices.
6. Follow the on-screen instructions: the app will automatically connect to the printer's temporary network (the name will be something like DIRECT-xx-HP Smart Tank 519).

Step 3: Select your home Wi-Fi network

7. The app will prompt you to select your home network from the list. If there is no network, tap Refresh the list or enter the name manually.
8. Enter your Wi-Fi password and click Connect.
9. Wait for confirmation: the printer will reboot and the indicator will turn off Wi-Fi will light up green.

After successful connection, the application will prompt:

• 📄 Print a test page.
• 📱 Set up printing by email (assign a unique email address to the printer).
• ☁️ Connect cloud services (Google Drive, Dropbox).

4. Method 3: Manual connection via WPS (for advanced users)

Method WPS (Wi-Fi Protected Setup) Allows you to connect your printer to the network without entering a password. However, it only works if:

• 🔄 Your router supports WPS (most modern models, for example, TP-Link Archer C6 or Keenetic, support).
• 🔒 The WPS mode is enabled on the router (usually activated by a button on the case).
• ⚡ The printer is within range of the router (no more than 5 meters).

Instructions:

1. On the printer, press and hold the button Wi-Fi until the indicator starts flashing quickly blue (WPS mode).
2. For 2 minutes press the button WPS on the router. Hold it for 3-5 seconds.
3. Wait until the printer light comes on. greenThis will take up to 1 minute.

If the indicator continues to flash orange, repeat the process or check:

• 🔌 Is the router powered by the network (sometimes it reboots after pressing WPS).
• 📵 Is there any interference from other devices (microwaves, wireless headphones).

⚠️ Attention: Some providers (eg MTS) disable WPS by default due to security vulnerabilities. You can enable it in the router's web interface at 192.168.1.1 (or 192.168.0.1) in the section Wi-Fi → WPS.

5. Checking the connection and troubleshooting

After setup, it's important to ensure the printer is actually connected to the network and ready to print. Here's how:

Verification methods:

ping [printer IP]

Common errors and solutions:

• 🚫 Error: "Failed to connect": Check your Wi-Fi password (case sensitive!). If the password is correct, reset the printer (hold Cancel And Wi-Fi 10 seconds).
• 🌐 The printer does not see the network: Make sure your router is broadcasting 2.4 GHz. If used 5 GHz, temporarily disable it in your router settings.
• 🔌 The indicator is flashing orangeThis indicates an authentication error. Restart the printer and router, then try setting it up again.

Via the printer control panel|

Via the HP Smart app|

Via WPS|

Another way|

6. Setting up printing from different devices after connection

Now that the printer is connected to Wi-Fi, you can use it from any device on your network. Let's cover the setup for the most popular platforms.

For Windows 10/11:

1. Open Settings → Devices → Printers & Scanners.
2. Click Add a printer or scanner.
3. Select HP Smart Tank 519 from the list. If it is not there, click The printer you need is not listed. and enter the printer's IP address (indicated in the connection report).
4. Install the drivers (Windows will download them automatically via Windows Update).

For macOS:

1. Open System Preferences → Printers & Scanners.
2. Click "+" → select a tab IP.
3. Enter the printer's IP address, protocol AirPrint and press Add.

For Android/iOS:

• Use the app HP Smart (already configured in the previous steps).
• To print from other applications (eg. Google Docs or Photos) select Print → HP Smart Tank 519.

For advanced users: If you want to customize printing email or through Google Cloud Print, open the printer's web interface. To do this, enter its IP address in the browser (e.g., 192.168.1.100). The default login and password are usually not required, but if asked, try admin/admin or look in the documentation.

7. Additional features: cloud printing and voice control

Printer HP Smart Tank 519 supports several useful features that make your work easier:

Cloud Printing:

• ☁️ Connect your account Google Drive, Dropbox or OneDrive in the app HP SmartNow you can print documents directly from the cloud without downloading them to your device.
• 📧 Set up print by email: the printer will be assigned a unique address of the form printer123@hpeprint.comSend emails with attachments to it—they will be printed automatically.

Voice control:

• 🎙️ Connect the printer to Google Assistant or To Alice from Yandex. To do this, use the app HP Smart go to Settings → Voice assistants and follow the instructions.
• Example commands:
  • "Okay, Google, print my shopping list."
  • "Alice, start scanning the document on the printer."

Automatic duplex scanning:

• 📑 The printer supports automatic scanning of double-sided documents into a single PDF file. To enable this feature, go to the app HP Smart select Scan → Settings → Duplex Scanning.

This feature is useful for business users. delayed printing: You can send a document to print, but it will only print at a specified time (for example, at night, when electricity is cheaper). This setting is available in the printer's web interface.

8. Frequently asked questions and solutions to problems

We've collected answers to the most frequently asked questions from users. HP Smart Tank 519If your problem isn't listed here, check the official documentation or contact HP support.

If none of the methods helped, please contact support. HP by phone 8-800-555-00-55 (call is free) or via chat on official website. Please tell me the printer model (Smart Tank 519) and a description of the problem - specialists will suggest an individual solution.