Multifunctional device HP Laser MFP 135w It's a compact solution for home offices where wireless printing is a standard convenience. The ability to print documents directly from a smartphone or laptop without unnecessary wires significantly simplifies document management. However, initial network connection setup often raises questions for users unfamiliar with the interface. HP Smart or the control panel of the device itself.
In this article, we'll take a detailed look at all the available methods for connecting this MFP to a wireless network. We'll cover setup via a USB cable, using the technology WPS and working with the mobile app. Understanding these processes will help you avoid common mistakes and get your device up and running quickly.
Before you begin, make sure your router is working properly and you know the password for your Wi-Fi network. It's also important that the computer or smartphone you'll be using for setup is already connected to the same network you plan to connect the printer to. Critical: The 135w series only supports 2.4GHz, so make sure your router is broadcasting this network and it is active.
Equipment preparation and requirements verification
The first step before starting setup is to properly prepare the device. Make sure that HP Laser MFP 135w Plugged into a power outlet and ready to use. The power indicator should be solid, not blinking. Place the printer close to the router during setup to avoid signal problems.
You'll need to know your wireless network name (SSID) and password to access it. If you haven't changed your router settings, this information is often found on a sticker on the bottom of the router. For complex corporate networks with web-based authentication, standard connection methods may not work without the help of a system administrator.
⚠️ Attention: Make sure your computer or smartphone's mobile data connection (3G/4G/5G) is disabled during setup. The device may attempt to use the mobile network instead of Wi-Fi, which will result in printer detection errors.
Please check if you have a free USB port on your computer if you plan to use the cable setup method. Although HP Laser MFP 135w Since the device is wireless, initial configuration often requires a temporary wired connection to transfer network parameters. The cable must be in good working order and support data transfer, not just charging.
Resetting the printer's network settings
If the device was previously used on a different network or the router settings were changed, you need to reset the printer's network settings. This will restore the network module HP Laser MFP 135w This will reset the settings to factory defaults and allow you to start the setup again. Ignoring this step may result in IP address conflicts or an inability to connect to the new access point.
To reset the printer, press and hold the wireless button on the control panel for a few seconds until the lights begin flashing. Alternatively, use the device menu, if available. The exact steps may depend on the firmware version installed on your MFP.
- 📶 Click the button Wireless on the control panel and hold it for about 5 seconds until the indicator flashes.
- 🔄 Wait until the power and wireless network indicators flash simultaneously, which indicates a successful reset.
- 📡 Make sure the Wi-Fi indicator starts flashing blue, indicating network search mode or setup mode.
After the reset, the device will enter connection standby mode. In this state, it can create its own access point. HP-Setup-135w, which can sometimes be seen in the list of available networks on your smartphone. Don't connect to it manually if you're using automated setup methods through the app.
☑️ Preparing for connection
Method 1: Setup using the HP Smart app
The most modern and convenient way to connect is to use the application HP SmartThis software is available for Windows, macOS, and iOS and Android mobile platforms. The app automatically detects new HP devices in the vicinity and offers a step-by-step setup wizard that takes care of most of the technical work.
Download and install the application HP Smart From the official store (Microsoft Store, App Store, Google Play) or from the manufacturer's website. After launching, click the "Add Printer" button or the plus sign. The program will ask you to enable Bluetooth on your device to initially search for the printer.
When the application finds HP Laser MFP 135w, it will ask you to confirm the setup process. You'll be prompted to select your Wi-Fi network from a list. The password is usually automatically entered from the system settings, but you can enter it manually. During the setup process, the app will transfer the network settings to the printer.
What should I do if HP Smart doesn't see my printer?
Make sure Bluetooth is enabled on your phone or laptop. Try restarting the app. If the issue persists, temporarily disable your antivirus or firewall software, which may be blocking the search for devices on your local network.
The wireless indicator on the printer will flash while the data is being transferred. Once the connection is successful, it will turn blue, and the app will notify you that the setup is complete. Now you can print documents, scan images, and monitor toner levels directly from your smartphone's screen.
Method 2: Connecting via USB cable
If the wireless method via the app doesn't work or you prefer the traditional approach, use a USB cable. This method ensures stable configuration data transfer even with an unstable Wi-Fi signal. You'll need a USB 2.0 Type-A to Type-B cable, which is often included in the kit but may require an additional one.
Connect the cable to the USB port on the back panel HP Laser MFP 135w and to an available port on your computer. Run the driver installation from the official website or use the installation disc if you have one. During the installation process, select "Wireless connection" or "Configure via USB."
The setup program will transfer network settings from your computer to the printer. Once the data is received, the MFP will attempt to connect to the router. Once the connection is established, the installer will report success and prompt you to disconnect the USB cable. Further printing will be done over the air.
| Parameter | Description | Value for HP 135w |
|---|---|---|
| Interface type | Connection standard | IEEE 802.11b/g/n |
| Frequency | Wave range | 2.4 GHz (only) |
| Security protocol | Data encryption | WPA2/WPA3 |
| Transfer speed | Maximum speed | up to 150 Mbit/s |
It's important not to disconnect the USB cable until the installer explicitly asks you to. Disconnecting it prematurely may interrupt the configuration process, and you'll have to start over. After successful setup, the computer and printer will be on the same subnet, ensuring fast response times.
Method 3: Using WPS technology
Technology Wi-Fi Protected Setup (WPS) Allows you to connect your device to the network without entering a password, simply by pressing a button. This method only works if your router supports WPS and this feature is enabled. HP Laser MFP 135w This is one of the fastest ways if physical access to the router is possible.
Press the WPS button on your router. Typically, you need to hold it for 2-3 seconds until the corresponding light on the router flashes. Then, within 2 minutes, press and hold the wireless button on the printer's control panel.
The printer will automatically detect the WPS signal from the router and exchange encryption keys. The Wi-Fi indicator on the device will blink while searching and connecting. Once the connection is established, the indicator will stop blinking and remain solid.
⚠️ Attention: Many modern routers have the WPS feature disabled by default for security reasons. If the router's button isn't responding, check the router's settings through the web interface.
If the printer's indicator light continues to flash or remains orange, the connection was unsuccessful. This may be due to a timeout (2 minutes) or incompatibility with security standards. In this case, try repeating the procedure or use the USB setup method.
Diagnostics and problem solving
Even if you strictly follow the instructions, difficulties may arise. Often, the problem lies in the frequency range: the router may broadcast a 5 GHz network, which HP Laser MFP 135w It just doesn't see it. Make sure you're trying to connect to a 2.4 GHz network. If the network names are the same, try temporarily separating them in your router settings.
Another common issue is a MAC address filter on the router. If you have a whitelist enabled, a new printer won't be able to access the network until you add its MAC address to the router settings. The MAC address can be found on a sticker on the device or by printing a configuration report.
- 🔍 Check if your computer's antivirus software is blocking communication with the printer.
- 📶 Make sure that the Wi-Fi signal where the printer is installed is strong enough (at least 2-3 bars).
- 🔄 Restart your router and printer—this solves 80% of IP address assignment problems.
To obtain a detailed network status report, press and hold the Cancel button (the cross) on the printer control panel for a few seconds, or use the Print Configuration button combination (depending on the firmware version). The report will include the IP address and connection status.
Frequently Asked Questions (FAQ)
Can the HP Laser MFP 135w be connected to a 5GHz network?
No, this model only supports the 802.11b/g/n standard, which operates in the 2.4 GHz band. If your router only broadcasts 5 GHz, the printer will not be able to connect. You must enable Dual Band or a 2.4 GHz guest network in your router settings.
What should I do if the wireless light is orange?
An orange light usually indicates a connection error or recovery mode. Try resetting the network settings by holding the Wi-Fi button. If this doesn't help, check the password entered correctly and the encryption type (it should be WPA2-AES).
Is a USB cable required for the printer to work continuously?
No, the USB cable is only required during the initial setup process unless you're using WPS or a direct app connection with a Bluetooth password. After successful setup, you can remove the cable, and the printer will operate completely autonomously via Wi-Fi.
How to find the IP address of a printer on the network?
Press and hold the Wireless button on the control panel until the light starts blinking, then release it. The printer may print a configuration report, which will list the IP address. You can also find the address in the HP Smart app under Printer Information.