In the age of digital entertainment, a smartphone's screen is no longer sufficient for comfortably watching videos or demonstrating presentations. Anycast — is a compact adapter that allows you to stream images from mobile devices and computers to a large TV screen wirelessly. Wireless data transmission technology is becoming increasingly popular as it eliminates the need to run long HDMI cables across the room.
However, the initial setup of the device often raises questions among users, especially when it comes to integrating the gadget into an existing home network. WiFi. Unlike simple enabling, correct configuration requires an understanding of how the protocols work. Miracast, AirPlay And DLNAProper settings ensure a stable picture without delays or connection interruptions.
In this article, we'll cover the connection process in detail, focusing on the nuances of using a home router. You'll learn how to switch your device to client mode so it connects to your main internet connection rather than creating its own access point. This will allow you to simultaneously use the internet on other devices and stream content.
Operating principle and connection modes
Adapters series Anycast operate on the basis of the operating system Linux and support multiple wireless media transmission standards. A key feature is the availability of two main operating modes: AP Mode (access point) and STA Mode (Client mode). Out of the box, the device is usually in access point mode, creating its own WiFi network to which your phone connects.
For comfortable use at home, you need to switch the gadget to client mode (STA). In this mode, the adapter connects to your main home router, just like a smartphone or laptop. This allows the device to access the local network and the internet, if required for streaming services.
⚠️ Note: When operating in Access Point (AP) mode, your phone may lose access to the mobile internet because the WiFi module is busy connecting to the adapter. Switching to Client (STA) mode solves this issue.
Switching between modes is accomplished through the device's built-in web interface. Accessing it doesn't require a global network connection; all configuration occurs locally. Understanding the difference between these modes is critical for troubleshooting connection issues in the future.
Technical details of the protocols
Miracast operates at the WiFi Direct level, creating a direct connection between devices, while DLNA uses the router's local network to transfer files. AirPlay requires specific emulation of Apple certificates.
Initial connection and interface access
The first step is to physically connect the adapter to the TV. The device is inserted into an available port. HDMI, and it is advisable to connect the power cable to an external outlet or power bank, since the voltage of the TV's USB port may not be sufficient for stable operation of the WiFi module.
After turning on the TV and selecting the appropriate signal source (button Source or Input on the remote), you'll see a start screen with the network name and connection password. This information is required for initial setup. Take your smartphone and, in the WiFi settings, find a network with a name similar to Anycast-XXXX.
Enter the password displayed on the TV screen. After a successful connection, your smartphone may notify you that internet access is unavailable. This is normal, as the adapter isn't yet connected to the router. Open any browser on your phone and enter the gateway IP address in the address bar.
The standard address for accessing the control panel is:
192.168.47.1If the page doesn't load, check the gateway address in your phone's WiFi connection details. The web configurator interface is typically minimalist and contains the main tabs for network configuration.
Setting up Client Mode (STA Mode)
After logging into the web interface, you need to find the section responsible for setting up WiFi. It may be called WiFi Settings, Network or InternetHere you need to change the operating mode with AP Mode on STA Mode (Station Mode). In this mode, the adapter will search for available networks to connect to.
In the list of available networks that opens, find the name of your home router. Click on it and enter the password for your home WiFi network. Make sure you enter the password correctly, maintaining proper case, as an error will prevent you from connecting.
- 📡 Select the name of your home network from the list of available ones.
- 🔑 Enter your WiFi router password in the appropriate field.
- 🔄 Click the button
ApplyorSaveto save the settings. - ⏳ Wait for the adapter to reboot, this will take about 10-15 seconds.
After rebooting, the device will attempt to connect to the router. If the password is correct and the signal is strong, a successful connection message will appear on the TV screen, along with a new IP address assigned by the router. From this point on, the adapter and your phone are connected to the same local network.
☑️ Checking the STA mode settings
Compatibility issues and frequency ranges
One of the most common reasons for unstable operation is incompatibility of frequency ranges. Most adapters Anycast operate in the range 2.4 GHz, while modern routers often distribute the network in the range 5 GHzIf your router only broadcasts 5 GHz, the adapter may simply not see the network.
The solution is to enable a 2.4 GHz guest network on your router or separate network names (SSIDs) for different frequencies in the router settings. It's also worth considering that the 2.4 GHz band is more susceptible to interference from microwave ovens and neighboring networks.
| Parameter | 2.4 GHz band | 5 GHz band |
|---|---|---|
| Transfer speed | Up to 150-300 Mbps | Up to 867 Mbps and higher |
| Penetration ability | High (better through walls) | Low (requires line of sight) |
| Compatibility | Supports all adapters | Only new Anycast M9+ models |
| Interference level | High | Short |
If you own a modern model, for example Anycast M9 Plus, it can support both bands. In this case, the preferred frequency setting will be available in the web interface. For 4K video transmission, 5 GHz is recommended.
Broadcasting images from various devices
Once the network is successfully set up, you can start broadcasting. The connection method depends on your smartphone's operating system. For devices based on Android the function is often called Broadcast, Smart View or Wireless monitor and is built into the notification curtain.
Users of technology Apple must use the function AirPlay. Just open the control center (swipe down or up depending on the model) and press Screen mirroringYour adapter should appear in the list of devices.
For computers running Windows 10/11 a key combination is used Win + K, which opens the wireless display connection panel. The system will find the adapter if Miracast is enabled.
- 📱 Android: Settings → Connections → Broadcast.
- 🍏 iOS: Control Center → Screen Mirroring (AirPlay).
- 💻 Windows: Win + K → Select a device from the list.
- 🌐 Chrome: Browser menu → Cast.
If the router is configured with Client Isolation, the wireless connection between the phone and the adapter will not be established.
Diagnostics and troubleshooting
Even with proper setup, glitches can still occur. Most commonly, users experience audio and video desynchronization or intermittent connection drops. This often indicates the device is overheating or lacking power.
Use an external power source (like a phone charger) instead of the TV's USB port. TVs often cut off power to the USB port when entering power-saving mode, which causes the adapter to reboot mid-movie.
⚠️ Note: Anycast firmware interfaces may vary depending on the version. If you don't see the steps described, please refer to the documentation for your specific model or try updating the firmware via the web interface.
If you see a picture but no sound, check your TV's audio settings. Sometimes you may need to manually switch the audio output to HDMI in your smartphone's settings. Also, make sure your phone's "Do Not Disturb" mode isn't enabled, as this can block system sounds.
If your adapter is completely inoperable, perform a factory reset. Most adapters have a small button on the body. ResetPress and hold it for more than 10 seconds until the indicator flashes.
Hidden commands for advanced users
Some firmware versions offer a hidden Debug section where you can manually change the screen resolution or disable the splash logo. Access to this section is often hidden from the average user.
Why doesn't the adapter see my WiFi network?
Most likely, your router only broadcasts in the 5 GHz band, while the adapter only supports 2.4 GHz. Enable mixed mode or the 2.4 GHz network in your router settings. Also, check if the network name is hidden (SSID Hide).
How to increase data transfer speed?
Move closer to the router and remove any obstructions. If your adapter model allows it, switch to the 5 GHz band. Close background apps on your phone that may be consuming data.
Is it possible to connect the adapter to the Internet via cable?
Most Anycast models do not have an Ethernet (LAN) port. However, some advanced versions (such as the M9 Plus) have a USB port that can be connected to a network card via an OTG adapter, though this requires complex setup.
The broadcast is delayed, can this be fixed?
Latency is inherent to Miracast/AirPlay technology and ranges from 0.5 to 2 seconds. This technology is not suitable for real-time gaming. You can reduce latency by lowering the output resolution in the adapter settings.