Managing a home router's wireless network is often necessary when it comes to enhancing data security or restricting children's internet access at night. Tattelecom offers subscribers a variety of equipment models, and the procedure for disabling the radio module can vary significantly depending on the device installed. In this article, we'll detail the steps for the most popular router models used in the provider's network.
Disabling the wireless module Wi-Fi It doesn't interrupt the wired connection, so you'll still have full internet access via an Ethernet cable on your computer or TV. This is an effective way to turn your router into a simple modem or protect your network from unauthorized connections while you're on vacation. Before making any changes, make sure you have access to the device's web interface or are prepared to connect to it via cable.
The first step is always to log into the router's control panel. To do this, open any browser on a device connected to the provider's network and enter the gateway's IP address in the address bar. The default address for most Tattelecom devices is 192.168.0.1 or 192.168.1.1If these addresses don't work, check the sticker on the bottom of the router, where the manufacturer specifies the exact IP address, as well as the login and password.
After entering the address, the system will request authorization. By default, the credentials are used admin / adminHowever, if you've previously changed your security password, please use it. If you lose your password, you'll need to perform a full factory reset using the button. Reset on the device body. Be careful, as after the reset, all user settings, including PPPoE, will be deleted.
Modern router interfaces may vary, but their underlying logic is the same. We'll cover the settings for the most common models, which are installed en masse by Tattelecom technicians. Understanding how the menus work will help you navigate even new firmware versions.
Disabling Wi-Fi on Sagemcom routers
Equipment brand Sagemcom (often F@st series models) is one of the most common devices in the provider's network. The interface of these devices is typically blue and white and has a clear structure. To access the desired option, go to the "Settings" tab in the top menu. Network or Local Network. Next, select the subsection Wireless or WLAN.
Here you will see the basic wireless network settings. Find the checkbox or switch labeled Enable Wireless or Wireless On/OffUnchecking this box completely deactivates the radio module. After doing this, don't forget to press the button Apply or Save at the bottom of the page for the changes to take effect. The router may reboot the network module, which will take a few seconds.
⚠️ Note: Disabling Wi-Fi will disable your wireless connection. If you configured your router via Wi-Fi, you will lose access to the control panel. Use a cable to complete the setup.
In some Sagemcom firmware versions, settings may be split into frequency bands. If your router is dual-band, you can disable the network. 2.4 GHz And 5 GHz separately. This is useful if you want to keep a fast channel for your TV but restrict access from mobile devices.
Wireless network settings on D-Link
Routers D-Link (DIR series) have their own recognizable interface, often in green or gray tones. To manage wireless network functions, go to the menu Wi-Fi or Wireless. On the left side of the screen or in the top navigation bar, find the item Basic settings (Basic Settings).
There will be a checkbox in the window that opens. Enable wireless connection (Enable Wireless). Uncheck this box. The D-Link interface often prompts you to confirm your actions, so after unchecking the box, be sure to press the button. Apply or SaveThe system may warn you about a connection break—confirm the action.
- 📶 Make sure you are editing the settings of the main network (SSID), not the guest network.
- 🔒 Changes take effect immediately after saving; rebooting the entire router is not required.
- 💡 The Wi-Fi indicator on the front of the device should turn off, indicating success.
If you have a newer version of the D-Link interface, the menu structure may be simplified. In this case, look for the wireless network icon on the main screen of the status bar. This often contains a quick toggle that allows you to manage the network status without diving deep into the menu.
Wi-Fi management on Eltex equipment
Optical terminals and routers Eltex (NTU and WEP series) have a more formal, technical interface. Access to the settings is standard via IP address. After authorization, go to the section WLAN or WirelessSelect a subsection from the menu Basic or General.
The parameter is located here Enable WLAN Radio or simply Radio On. Toggle this setting to on Disable or Off will stop the signal broadcast. A special feature of Eltex is that changes are often applied instantly, but to be on the safe side, it's best to reboot the device through the menu. System Tools → Reboot.
It's important to note that some Eltex models provided by the provider may have restricted access rights. If you don't see the on/off slider, your provider may have blocked this feature remotely. In this case, the only solution is to contact technical support or use hidden menus, if available.
Eltex Hidden Settings
On some Eltex NTU-4W models, advanced radio interface settings are hidden in the Advanced menu. To access them, you may need to switch the display mode at the top of the screen to "Expert" or "Advanced."
Table: Comparison of settings paths for different models
To help you quickly navigate the interfaces of various devices, we've prepared a summary table. It will help you quickly find the menu item you need depending on the brand of your equipment.
| Router model | Menu section | Subsection | Option name |
|---|---|---|---|
| Sagemcom | Network | Wireless | Enable Wireless |
| D-Link | Wi-Fi | Basic settings | Enable wireless connection |
| Eltex | WLAN | Basic | Enable WLAN Radio |
| Huawei | WLAN | WLAN Basic Configuration | WLAN Switch |
Alternative methods: Mobile app and button
Modern technologies make it possible to manage your network using more than just a browser. Many Tattelecom routers support mobile app management, for example, Dom.ru or the operator's proprietary app. If your router is linked to your account, you can find the Wi-Fi switch directly on the app's main screen. This is the fastest way to temporarily disable the network.
A physical button on the case is another option, but it doesn't work on all models. Look closely at the buttons on the front or back panel. If there's a button with an antenna icon or text Wi-FiA short or long press (3-5 seconds) can disable the wireless module. The indicator light on the housing should go out.
⚠️ Note: On some router models, long-pressing the Wi-Fi button may initiate the WPS process or a factory reset. Be careful and test the device's response with a short press.
Using an app often gives you more control. For example, using your smartphone, you can not only turn off the network, but also pause it for specific devices or set time intervals. This is more convenient than having to go into your browser settings every time.
☑️ Check before disconnecting
Common problems and their solutions
Sometimes users encounter a situation where settings aren't saved or Wi-Fi re-enables after a reboot. This could be caused by a firmware glitch or a settings conflict. Try clearing your browser cache or using incognito mode to access the router settings. This will eliminate the possibility of old scripts interfering with your router's settings.
If your router persistently restores Wi-Fi settings, your ISP may be enforcing a remote management policy (TR-069) that resets the configuration to default. In this case, changing your Wi-Fi password to a complex and unique one may be more effective than completely disabling it, as no one will be able to connect without your permission.
The problem could also be due to electromagnetic interference or a faulty module. If the Wi-Fi indicator is on but the network isn't detected by devices, or if it doesn't go out after being disconnected, the device may need to be reflashed or replaced at a service center.
Questions and Answers (FAQ)
Does turning off Wi-Fi affect wired internet speed?
No, disabling the wireless module does not affect the speed or stability of a wired connection. In fact, it may even slightly reduce the load on the router's processor, theoretically improving its performance.
Is it possible to turn off Wi-Fi remotely when away from home?
This is only possible if you use the operator's official mobile app or have configured remote access to the router in advance. This cannot be done through the standard web interface from an external network (without port forwarding).
Will IPTV work after Wi-Fi is disconnected?
Yes, TV will work if the set-top box is connected to the router via a LAN cable. If the set-top box is connected via Wi-Fi, streaming will be interrupted.
How do I turn Wi-Fi back on?
You need to log into the router settings again via a cable connection and check the box. Enable Wireless (or similar) in the appropriate menu section, then save the settings.