Modern office and home tasks require high mobility, and wired connections often become a limiting factor. Wireless network allows you to place the device in any convenient location where there is signal coverage, eliminating the need to run cables across the entire room. Model HP Laser 107w (also known as the 107wr series) features built-in Wi-Fi, making it much easier to organize your workspace.
However, initial setup may raise questions for users who have previously used only wired models. The activation process wireless mode Requires several steps to be completed in sequence, from preparing the equipment to installing drivers on the computer. In this article, we'll cover all available connection methods in detail.
You'll learn how to use the WPS button for instant synchronization, how to set up your device via USB cable if your router doesn't support automatic connection, and how to use the mobile app. HP SmartWe'll also cover common errors and how to troubleshoot them to ensure your printer always remains accessible on the network.
Preparatory steps before starting setup
Before you begin configuring network settings, you must ensure that all system components are ready for operation. Make sure that router It's turned on and distributes the Internet, and the printer itself HP Laser 107w The device is filled with toner and has no errors on the display. The distance between the device and the router during setup should be minimal to ensure stable signal reception.
It's important to check which operating system is installed on your computer or laptop, as this may affect the driver installation method you choose. For proper operation Wi-Fi module It is recommended to use a 2.4 GHz network for your printer, as some models may not see 5 GHz networks in setup mode.
If you have previously tried to set up your device and the process was interrupted, you may need to perform reset network settingsTo do this, press and hold the wireless button (antenna icon) and the cancel button (cross) simultaneously on the control panel for a few seconds until the indicators flash. This will reset the network settings to factory defaults.
⚠️ Attention: Make sure that Client Isolation is not enabled on your router, otherwise your computer will not be able to "see" the printer on the network, even if both devices are connected to the same Wi-Fi.
It's also a good idea to prepare a USB Type AB cable (square connector), which is often included in the kit, or purchase one separately. You'll need it for the cable setup method, which is the most reliable way to transfer network data to the device.
Connection method via WPS button
The fastest way to integrate HP Laser 107w To connect to your local network, use WPS (Wi-Fi Protected Setup) technology. This method allows you to automatically transmit the network password, eliminating the need to manually enter it on a computer keyboard or through complex printer menus.
First, find the button marked on the body of your router. WPSIt may be a physical button or a software button in the router interface. On the printer's control panel, locate the wireless button. Press and hold it until the power and wireless lights begin flashing simultaneously.
Within two minutes of activating the printer's search mode, press the WPS button on the router. If the connection is successful, the wireless indicator on the control panel will light up. HP Laser 107w The LED will stop flashing and remain solid. This means the device has received an IP address and is ready to use.
If the lights continue to flash or are intermittent, the connection is not established. Check whether your router supports the WPS standard and whether the pairing timeout has expired. Sometimes you may need to repeat the process, after first powering both devices off and on.
Setting up Wi-Fi using a USB cable
If the automatic method doesn't work or your router hides the SSID (network name), use the wired method for initial configuration. This method is considered the most stable, as it eliminates errors when manually entering the password. You will need to download the full driver and utility package for your model from the manufacturer's official website. HP Laser 107w.
Run the setup file on your computer and follow the on-screen instructions. When prompted to select a connection type, select "Wireless Connection." The installer will prompt you to connect USB cable between your computer and printer. At this point, the program will automatically read your PC's current network settings and transfer them to the printer.
☑️ USB Setup Checklist
Once the data transfer is successful, the program will notify you that the setup is complete, and you can disconnect the USB cable. The printer will save the network settings in its memory and will automatically connect to the router each time it is turned on. The Wi-Fi indicator on the device should be constantly lit.
| Indicator | State | Meaning |
|---|---|---|
| Wireless communication | It's blue | Connected to the network |
| Wireless communication | Flashing blue | Setup Mode / Error |
| Wireless communication | Turned off | Wi-Fi is disabled |
| Wireless communication | Flashing orange | Problem with signal |
It's important to note that after setting up via USB, the drivers on your computer will also be installed in network mode. This means you'll be able to print wirelessly, eliminating the need for a cable.
Using the HP Smart app for mobile devices
HP has developed an application for smartphone and tablet users. HP Smart, which allows you to configure settings directly from your mobile device. This is especially convenient if you don't have a computer with a USB port nearby. The app is available for iOS and Android and requires HP account registration.
Before you begin, make sure your smartphone is connected to the same Wi-Fi network you want to connect the printer to. Turn on Bluetooth on your phone, as the app uses it to detect the device. HP Laser 107w At the initial stage. Open the app and tap "Add Printer" or the plus sign.
Follow the instructions on your mobile device. If the printer is in setup mode (the indicator light is flashing), the app will prompt you to share your Wi-Fi password. This method is often faster than searching for drivers on your computer and allows you to start printing photos or documents right away.
What should I do if the app doesn't see the printer?
Make sure the wireless indicator on the printer is on or blinking. If it's off, press and hold the Wi-Fi button for 3 seconds. Also, make sure location and Bluetooth are enabled on your phone, as they are required for the app to work.
Once your device is successfully added to the app, you'll be able to not only print, but also monitor toner levels, scan documents, and email them. HP Smart makes printer control as convenient as possible for the modern user.
Installing drivers and software
After physical connection Once the network is established, you need to install software on your computer so that the operating system can interact correctly with the device. HP Laser 107w It is best to use the full driver package rather than the basic Windows tools, as it contains additional diagnostic tools.
Go to the official HP support page and enter your device model. The system will prompt you to download the recommended driver. During installation, select "Wireless Connection" if prompted. The program will find the printer on the network using its IP address.
If the automatic search doesn't yield results, you can add the printer manually through the Windows Control Panel. To do this, go to "Devices and Printers," select "Add a printer," and select "The printer I want isn't listed." Then, select "Add by TCP/IP address."
You can find your printer's IP address by printing a network configuration report. To do this, press and hold the wireless button on the printer's control panel for 5-10 seconds. The report will show the current IP address, which must be entered into the installation wizard.
⚠️ Attention: Operating system interfaces and support web pages are subject to change. If installation steps differ from those described, please refer to the current prompts on your monitor.
Diagnosing problems and resetting network settings
During operation, situations may arise where the printer stops responding or loses connection to the router. This is often due to a change in the Wi-Fi password or replacement of the provider's equipment. In such cases, it is necessary to reset the network settings. HP Laser 107w.
To reset, press and hold the Wireless and Cancel buttons simultaneously for 5 seconds. The lights will flash, and the printer will reboot the network module. After this, it will enter connection standby mode, and the Wi-Fi light will begin flashing.
If the problem is a weak signal, try changing the location of your router or printer. Walls, metal structures, and household appliances can interfere with the radio signal. 2.4 GHz band typically provides better coverage within an apartment than 5 GHz.
It's also worth checking whether your firewall or antivirus software is blocking the printer connection. Temporarily disable your firewall to test. If printing resumes, add the device to your security software's exception list.
Frequently Asked Questions (FAQ)
Can the HP Laser 107w be connected to a 5GHz network?
Model HP Laser 107w Only supports the 802.11 b/g/n standard, which operates in the 2.4 GHz band. If your router broadcasts a 5 GHz network, the printer won't see it. You'll need to enable 2.4 GHz network broadcasting in your router's settings.
What should I do if my Wi-Fi indicator is flashing orange?
A blinking orange light usually indicates a connection error or a weak signal. Try moving the printer closer to the router. If this doesn't help, reset the network settings and try connecting again via USB or WPS.
Do I need to keep the USB cable connected all the time?
No, the USB cable is only required during the initial setup if you choose the cable configuration method. After the Wi-Fi settings have been transferred, the cable can be disconnected, and the printer will operate completely wirelessly.
How to find the IP address of a printer on the network?
The easiest way is to print a network configuration report by holding down the wireless button for 5-10 seconds. You can also view the IP address in the app. HP Smart or in the list of connected clients in your router's interface.