HP 4729: How to Connect Wi-Fi and Set Up a Network

Modern office work requires high mobility and flexibility, and wireless connection printer is becoming a standard, not a luxury. Model HP LaserJet Pro 400 MFP M4729 (often referred to simply as the HP 4729) is a powerful multifunctional device that can operate anywhere within your local network coverage area. Properly configured, this device allows you to print, scan, and fax directly from your smartphone or tablet without the need for unnecessary cables.

Integration process M4729fdw Enabling wireless networking can seem complicated due to the numerous functions and buttons on the control panel. However, if you break the procedure down into sequential steps, the task becomes quite manageable, even for a novice user. In this guide, we'll cover all the current methods for activating wireless mode, including using WPS, manual configuration via the touchscreen, and the classic USB cable connection.

Before you begin, make sure your router is working properly and providing internet access, and that your printer is loaded with toner and ready to use. Signal stability Wireless network plays a critical role in print speed, so it's recommended to place the device in a strong reception area. If the printer is placed in a niche or far from the router, connection interruptions may occur when transferring large documents.

Preparing equipment and checking network parameters

The first step is to physically prepare the device for setup. Make sure that HP 4729 Plugged into a power source and fully booted. The control panel lights should be solid and not flashing in standby or error mode. If the device is freshly unpacked, it may go through an initial calibration process, which takes several minutes.

You need to know the name of your wireless network (SSID) and its password. Without this information, automatic configuration is impossible. Pay attention to the case of letters and symbols in the password, as the system distinguishes between uppercase and lowercase characters. It's also important to ensure that the router doesn't use MAC address filtering, which could block the new device.

⚠️ Note: If your router distributes the network at 2.4 GHz and 5 GHz frequencies under different names, make sure that you are trying to connect the printer to the 2.4 GHz network, as older modules may not see 5 GHz, although M4729fdw Typically supports both bands, but prefers 2.4 GHz for stability.

We recommend temporarily disabling the VPN on the computer or smartphone you plan to use to control the printer to avoid routing conflicts. It's also worth checking that the list of connected devices on your router isn't full, as this limit can be reached, especially in offices with a large number of devices.

Using WPS technology for fast synchronization

The easiest way to connect HP LaserJet Pro 400 MFP M4729 to Wi-Fi without entering a password, is a technology WPS (Wi-Fi Protected Setup). This method works if your router also supports this feature and has a dedicated button. The process takes just a few seconds and doesn't require a computer.

To get started, find the button with an antenna or wireless network icon on the printer's control panel. Press it to enter the wireless connections menu. On the touchscreen, select "Wi-Fi Protected Setup" or "WPS Setup." The device will wait for a command from the router.

• 📶 Press the WPS button on your router (usually you need to hold it for 2-3 seconds until the indicator light starts flashing).
• 🖨️ On the printer screen, select the "Push Button" method and press "Start" or "OK".
• ⏳ Wait about 2 minutes until the wireless light on the printer stops flashing and turns solid blue.

⚠️ Note: WPS mode is often disabled by default for security reasons or may be incompatible with some ISP routers. If the connection is not established after 2 minutes, try another method.

After a successful connection, a success message will appear on the screen, and the printer will automatically print a network configuration report. This document contains the device's IP address, which may be needed for further fine-tuning or installing drivers on desktop computers.

Manual Wi-Fi setup via the control panel

If the automatic setup does not work, you need to perform manual configurationThis is a more secure method, as it allows you to precisely select the desired network from the list of available ones and enter the password correctly. Interface HP 4729 Equipped with a color touch screen, which makes menu navigation intuitive.

Tap the wireless network icon (antenna) on the home screen or at the top of the display. If the icon is gray or has a line through it, tap it to activate the wireless module. In the menu that opens, select "Wireless," then go to "Wireless Setup Wizard."

The printer will begin searching for available networks within range. Select your router's name from the list that appears. If your network isn't listed, check to see if the SSID is hidden and enter the name manually if necessary. After selecting the network, a virtual keyboard will open for entering the password.

Be careful when entering characters, especially if the password contains special characters. Use the Aa key to enter capital letters. After entering the password, click "Done" or "OK." The printer will attempt to obtain an IP address from the router's DHCP server.

Connection via USB cable and software

Sometimes wireless setup via the control panel can be inconvenient due to a complex password or specific corporate network conditions. In such cases HP suggests using a temporary USB connection to transfer network settings. This method is considered the most reliable for initially installing drivers on a computer.

You will need to download the full software package from the official website. HPRun the installation file on your computer and follow the on-screen instructions. When prompted to select a connection type, select "Wireless Connection" and follow the prompts.

At a certain point, the installer will ask you to connect the printer to your computer using a USB cable. Important: Don't connect the cable prematurely, otherwise the program may not recognize the device correctly. After connecting the cable, the program will automatically transfer the Wi-Fi settings from your computer profile to the printer.

Once the program confirms the printer is connected to the network, it will prompt you to disconnect the USB cable. After this, the device will continue to operate wirelessly, and you'll be able to print from any device on the same network.

Setting up Wi-Fi Direct for printing without a router

Function Wi-Fi Direct Allows you to connect mobile devices directly to the printer, bypassing your home or office network. This is ideal for quickly printing documents from a guest's phone or when the main router is temporarily unavailable. The printer HP 4729 creates its own access point.

To activate this feature, press the Wireless button on the control panel, then select "Wi-Fi Direct." Make sure the status is set to "On." The printer's network name (e.g., HP-Print-xx-LaserJet 400 M4729) and the connection password will be displayed on the screen.

• 📱 Open Wi-Fi settings on your smartphone or tablet.
• 🔍 Find the name that matches your printer model in the list of networks.
• 🔑 Enter the password on the MFP screen (it can also be found in the configuration report).

Once connected, you can send documents to print via the app. HP Smart or standard operating system tools. Please note that while your device is connected to Wi-Fi Direct, it may not have internet access unless your smartphone is configured to automatically switch between networks.

⚠️ Please note: Wi-Fi Direct mode may reduce printer performance when other network modules are active. For continuous office use, it's best to connect through a central router.

Diagnosing and resolving connection problems

Even with the correct setup, situations may arise when HP 4729 The printer loses network connection or doesn't detect the router. Often, the problem lies in incompatible encryption standards or a buffer overflow in the printer's network settings. First, try rebooting both devices: the router and the MFP.

If the wireless indicator is blinking blue, it means the printer is trying to connect but is unable to. If it is solid blue, the connection is established. If the indicator is off or amber (orange), the Wi-Fi module is disabled or an error has occurred. In this case, check whether "Airplane Mode" is enabled in the printer's network settings.

A common issue is changing your Wi-Fi password. If you've changed the password on your router, your printer won't connect automatically. You'll need to reset the network settings on the printer itself. To do this, go to "Settings" (gear icon) → "Network" → "Restore network settings."

It's also worth checking whether your computer's antivirus software is blocking communication with the printer. Temporarily disable your firewall to test. If the problem persists, try assigning it to the printer. static IP address in the router settings so that it does not change every time you reconnect.

Why can't my HP 4729 printer see my Wi-Fi network?

Most likely, the router is only broadcasting on the 5 GHz band, but the printer is trying to find 2.4 GHz networks, or vice versa, the network name is hidden. Make sure SSID broadcasting is enabled on the router and the 2.4 GHz band is activated.

How to find the IP address of the HP M4729 printer?

Click the wireless icon (antenna) in the control panel. In the menu that appears, select "View details" or "Configuration report." The IP address will be listed in the IPv4 section.

Is it possible to connect HP 4729 to a hidden network?

Yes, this is possible. When setting up manually, select the "Enter network name" option (or similar) at the very bottom of the list of available networks and enter the SSID manually, taking care to ensure proper case-intelligibility.

What does a blinking blue Wi-Fi light mean?

A blinking blue light indicates that the wireless module is active, connecting to the network, or transmitting data. If the blinking continues for a long time, the password may be entered incorrectly or the signal is too weak.